Ask Experts Questions for FREE Help !
Ask
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
    		  
    #1

    Nov 18, 2007, 04:05 AM
    Disassembly of Delta model #2476 to replace diverter
    Private Message: Delta Waterfall kitchen faucet, model 2476
    Today, 02:40 AM
    avdpierre
    New Member Join Date: Nov 2007
    Posts: 2


    Delta Waterfall kitchen faucet, model 2476

    ------



    I have a Delta Waterfall kitchen faucet, model#2476 and have determined (through Delta) that the diverter needs to be replaced. Problem: I cannot get the spout off. I have the diagrams for removal but the diagram does not indicate how to loosen the spout. It appears to have some time of retaining clip near the base, but all efforts to remove have failed. I did receive one suggestion to turn the spout to the right to 'lift it off', still cannot get it off. I also replied to the answer I was given and attached picture of the base of the spout... still no response and I am sort of desperate... I cannot run my portable dishwasher until I replace the diverter. Do you have any suggestions?
    Thanks
    Could not find a place to attach my photo of the base of the faucet
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
    		  
    #2

    Nov 18, 2007, 05:52 AM
    Click on; http://www.deltafaucet.com/media/Pro...1RevB_9669.pdf
    To see diagrams and instructions. Good luck, Tom
    doug238's Avatar
    doug238 Posts: 1,560, Reputation: 62
    Ultra Member
    		  
    #3

    Nov 18, 2007, 09:50 AM
    On the water fall, you pull the trim piece up at the base of the spout, it is not screwed on, it simply slides up. Then there is a plastic piece that is cut, kind of like an outside snap ring that peels off. Then the spout lifts straight up by twisting.
    avdpierre's Avatar
    avdpierre Posts: 3, Reputation: 1
    New Member
    		  
    #4

    Nov 18, 2007, 11:56 AM
    Comment on doug238's post
    I was able to fix the problem. Thanks so much for your help!
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Disassembly of Delta model #2476 to replace diverter [ 2 Answers ]

I have a Delta waterfall/#2476 and have determined (through Delta) that the diverter needs to be replaced. Problem: I cannot get the spout off. I have the diagrams for removal but the diagram does not indicate how to loosen the spout. It appears to have some time of retaining clip near the base,...

Diverter stem replace [ 1 Answers ]

I Already Change The Diverter Stem On My Bathroom Shower. I Installed A New One (sayco). It Works Ok, Except When I Rotote It To Change And Send Water Only On Top Shower, Because It Send Also Water To The Bottom Shower (both ways). Do It Have Any Particular Way To Install It? Do I need to...

Delta diverter stem stuck [ 4 Answers ]

We have a three handle delta faucet in our bath/shower. When turned to use the shower only half of the water comes out the shower the other half still comes out of the faucet. We assume we need to change the stem but we can't get it out. There isn't a nut or anything that seems to be holding it...

Trying to replace Weird Size Tub Spout Diverter [ 3 Answers ]

When I pull up my Diverter for my shower, It sprays a lot and cuts down on my shower's stream. So I decided to replace it yesterday. I determined that it is the screw on type and removed it. But when I took it off I noticed that there was a 1/2 inch copper pipe with a 1 1/4 inch thread attached...

Need to replace tub diverter - stressed out [ 1 Answers ]

Hi, This is my first home and much to my surprise, the shower doesn't work. I did some research and found that part of my problem is that the diverter in the tub has corroded away and now the water only comes from the spout, not the shower. We are trying to take off the spout to replace it,...

View more questions Search