Ask Experts Questions for FREE Help !
Ask
    cenusa's Avatar
    cenusa Posts: 4, Reputation: 1
    New Member
    		  
    #1

    Mar 3, 2014, 10:00 PM
    Bryant 383kav024070 code 13
    Hi guys I am new to this forum. I have some problems with my bryant furnice. For some reason it is giving me a 13 code flame roullout switch. I have to manually reset the switch. It will run fine for a while but after that the switch has to be reset again. Now the furnice can run fine for a week without having to reset the switch or it can run for a few hours. It depends. What should I check on it. If you guys could give some advice and suggestions that will be great. Thank you so much
    ma0641's Avatar
    ma0641 Posts: 15,675, Reputation: 1012
    Uber Member
    		  
    #2

    Mar 4, 2014, 09:35 AM
    Make sure all the orifices are open in the burner tubes. Trane has thin slits that sometimes get clogged with rust. Brush and vac out the burners.
    cenusa's Avatar
    cenusa Posts: 4, Reputation: 1
    New Member
    		  
    #3

    Mar 4, 2014, 04:14 PM
    Quote Originally Posted by ma0641 View Post
    Make sure all the orifices are open in the burner tubes. Trane has thin slits that sometimes get clogged with rust. Brush and vac out the burners.
    I will look at them this evening. I took them aut last year and cleand them. But I will do it again

    Thank you for the advice and I will post back to let you know if it worked
    cenusa's Avatar
    cenusa Posts: 4, Reputation: 1
    New Member
    		  
    #4

    Mar 4, 2014, 07:06 PM
    So I took out the burners. They were a bit dusty but clean. I cleaned them again and I cleand the flame sensor too. I will see I this was the problem
    cenusa's Avatar
    cenusa Posts: 4, Reputation: 1
    New Member
    		  
    #5

    Mar 22, 2014, 08:34 PM
    The problem is still there even after the burners have been cleaned. Any other suggestions. Thank you
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Bryant Plus 80 Code 33 [ 10 Answers ]

I have a Bryant Plus 80 that is throwing a error of 33 (limit or flame roll out switch is open). The last time this happened was because the hot surface igniter was broken (frequent problem as my furnace has a tendency to short-cycle). I had picked up a couple extra ones so I had them on hand to...

Plus 90 bryant code 23 [ 0 Answers ]

I disconnected one wire to the pressure switch, reconnected it and the draft inducer started and all was well, for overnight... same problem and solution in the AM.. do I need to replace the pressure switch?

Bryant code 42 [ 1 Answers ]

When the furnace is given the self test all appear to run fine the inducer hi and low, blower high and low and igniter glows. Furnace shuts down after about 2 min on high output. Could it be the control board?

Bryant code 33 [ 1 Answers ]

Bryant gas funace model 310aav042090aaja. Code 33. Wired around limit and it worked fine. Replaced with new limit throws code again. Vents clear. Filter clear. What next? Is it really getting too hot? Runs about 4 minutes before throwing code and cycles down about 3 minutes.

Bryant plus 90 code 43 [ 0 Answers ]

I have a Bryant Plus 90 series. I'm getting a code 43. From what I gather in my search, does it have anything to do with the blower motor?

View more questions Search