Ask Experts Questions for FREE Help !
Ask
    nkolber's Avatar
    nkolber Posts: 3, Reputation: 1
    New Member
     
    #1

    Sep 27, 2009, 03:54 PM
    Intertherm mmhb 056 electric ignition furnace
    Getting flashing light two times-indicates that control ion lockout due to signal not received by control that inducer pressure switch not closed n time, please help! p.s recently replaced ignightor and thermostat
    T-Top's Avatar
    T-Top Posts: 1,871, Reputation: 100
    Ultra Member
     
    #2

    Sep 27, 2009, 06:13 PM
    If it's a 90% furnace make sure the condensate drain is clear. Check for restrictions in the vent pipe.
    nkolber's Avatar
    nkolber Posts: 3, Reputation: 1
    New Member
     
    #3

    Sep 27, 2009, 06:36 PM

    Where is the drain?
    T-Top's Avatar
    T-Top Posts: 1,871, Reputation: 100
    Ultra Member
     
    #4

    Sep 27, 2009, 06:55 PM
    Is your furnace vented with metal vent or pvc pipe?
    nkolber's Avatar
    nkolber Posts: 3, Reputation: 1
    New Member
     
    #5

    Sep 27, 2009, 07:00 PM

    Metal, it's a mobile home, checked vent on roof, does not seem to be blocked
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
     
    #6

    Sep 27, 2009, 09:53 PM
    See wiring diagram PAGE 1 on below doc. You do not have a pressure switch in that unit you have a Centrifugal Switch built into the small combustion motor/blower. This unit is a Direct Combustion burner style.

    NOTE: if this unit is on LP Gas and you do not know what you are doing I highly suggest you call a professional that does. With LP gas these babies go BANG if you try and jumper out the centrifugal switch for testing purposes.

    If using Natural gas it is not quite as bad but still will go bang. Just a friendly warning. The switches do stick in these small combustion motors.

    http://www.centraltrailer.com/resour....mm_wiring.pdf

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Intertherm electric furnace [ 1 Answers ]

Can anybody give me step by step instructions for where the furnace wires go from the furnace to the new 60 amp breaker kit for an intertherm electric furnace. Hooked this up yesterday and the furnace is not blowing out hot air only warm?

Intertherm Electric Furnace [ 3 Answers ]

The electric furnace makes clicking sounds (relays switching? ) and feels very warm to the touch, despite a thermostat setting of 60 deg F in July. The fan is set to AUTO and did not run at all. Are the relays shot and requiring replacement?

Intertherm electric furnace [ 3 Answers ]

I have an Intertherm electric furnace model MAC 2260A, serial # F000156739. It only blows cold air, so I am assuming the heating element has failed. I have had great difficulty finding a replacement. Any ideas where I can find one? Should I be looking at something else as the problem, as well?...

Intertherm electric central furnace [ 4 Answers ]

I have an Intertherm Central electric furnace model FEH-017H-C It has run perfect for years but lately the fan will not always start up. The thermostat clicks on the heater coils and after about 12 seconds the fan kicks in and circulates the warm air. Occasionally the thermostat clicks...

Intertherm electric furnace [ 1 Answers ]

I have an Intertherm E1EB-015HA electric furnace I recently had A/C Relay problems with it and since it is 10yrs. Old I thought I would just rebuild the whole thing. So I replaced the sequencers, limit switches, ac relay, transformer, and start capasitor, and installed a new digital non...


View more questions Search