Ask Experts Questions for FREE Help !
Ask
    jackath100's Avatar
    jackath100 Posts: 4, Reputation: 1
    New Member
     
    #1

    May 30, 2010, 03:22 PM
    My honda crv makes a grinding noise when turning
    The noise only occurs on slow turns, it is in both directions. It sounds like rubber turning on a smooth surface.
    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #2

    May 30, 2010, 04:17 PM

    Possibilities:

    . Strut Mounts--rubber bushing may be causing the noise.

    . Stabilizer Bar End Links.
    jackath100's Avatar
    jackath100 Posts: 4, Reputation: 1
    New Member
     
    #3

    May 30, 2010, 04:26 PM
    Any chance it is the all wheel drive and a need for that fluid to be changed?
    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #4

    May 30, 2010, 04:41 PM

    As TxGreaseMonkey, I can say you definitely want to change all fluids when specified in your Owner's Manual. However, you particularly mentioned the rubber sound, which my suggestions took into consideration. I don't think the all-wheel drive would be a factor.
    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #5

    May 30, 2010, 04:44 PM
    Try disconnecting both Stabilizer Bar End Links and see if the noise goes away. If it does, then you have identified the source of the noise. End links are pretty notorious for making noise. I've had new ones start making noise after 20,000 miles or less. If you end up buying replacements, be sure to get a set that comes with a lifetime warranty.
    jackath100's Avatar
    jackath100 Posts: 4, Reputation: 1
    New Member
     
    #6

    Jun 1, 2010, 11:02 AM

    Thank you so much!
    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #7

    Jun 1, 2010, 11:18 AM

    Did you find out the source of the noise?
    jackath100's Avatar
    jackath100 Posts: 4, Reputation: 1
    New Member
     
    #8

    Jun 2, 2010, 12:39 PM

    I am going to take it into my mechanic and have them check it out. I wanted to get an idea about what it could be before I brought it in so your responses have been very helpful- thank you

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Grinding noise when turning right [ 8 Answers ]

Toyota Corolla 2002 I went on vacation for two weeks (car sat in driving for the duration). After I came back I noticed that every time I make a right turn I hear this grinding noise. The noise seems to be consistent with the speed (i.e. if my speed is fast then the grinding noise is fast). I...

Whirlpool dryer makes a grinding noise and a burning smell [ 1 Answers ]

When I press start, I hear a loud grinding noise (like metal on metal) and smell a burning noise. I quickly turned off the dryer so as not to burn out anything. I looked inside the dryer, and felt around the edges for a lodged piece of metal/coin. There was none. I spun the drum, by hand, and...

Grinding noise when turning wheel [ 7 Answers ]

Hello, I was hoping someone could give some feedback on my issue. I just purchased a 95 Lincoln Continental. 94k miles. I notice that when I turn the wheel left, it makes a grinding or growling noise. The noise stops when I stop turning the wheel. I looked under the front and noticed CV boot ripped...

Grinding noise turning right [ 2 Answers ]

I have a 1999 Pontiac Grand AM and yesterday I started hearing a grinding noise when I make a right hand turn. Any thoughts?

Starter makes bad grinding noise [ 1 Answers ]

I pulled out the starter and the teeth were ground off. I installed a new starter, and the same thing happened. The car is a honda civic with a d15b2 engine.


View more questions Search