Ask Experts Questions for FREE Help !
Ask
    ruddle's Avatar
    ruddle Posts: 3, Reputation: 1
    New Member
    		  
    #1

    Oct 15, 2009, 06:20 AM
    Nordyne Heat Furnace Blower
    I have a Nordyne heater in a 1996 mobile home. My A.C. works normal. I can also switch the blower to ventilate and it works normal. But, when I switch the thermostat to heat. The blower will not come on. I can see the furnace heating up, but that it. According to the diagram, this unit does have 2 sequencers. Please help.
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #2

    Oct 15, 2009, 09:30 AM
    If this is an electric unit the heat sequencers could control the blower in the heat mode but some Nordyne electric units have used a small circuit board. Refer to your wiring diagram on the unit.
    ruddle's Avatar
    ruddle Posts: 3, Reputation: 1
    New Member
    		  
    #3

    Oct 15, 2009, 09:45 AM

    Yes, this is a electric heater. Are the sequencers easy to replace? Are they bolted in position?
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #4

    Oct 15, 2009, 09:52 AM
    First they usually have a lot of electric wires on them so you better know exactly what you are doing. They are usually bolted or screwed into the metal mounting area.

    If you mess up the wiring you will be toast.
    ruddle's Avatar
    ruddle Posts: 3, Reputation: 1
    New Member
    		  
    #5

    Oct 15, 2009, 09:57 AM

    Thanks for the advice. I'm am not reast to meet my maker just yet. Therfore, I will have to call a repairman. Thanks
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #6

    Oct 15, 2009, 10:16 AM
    No problem
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Furnace blower on - no Heat [ 20 Answers ]

I have a Carrier furnace with an automatic ignition. The fan is constantly running but it is not heating. Additional Information: Model 58PAV: The Red Led Status light is rapidly flashing - which according to the manual means 'Line voltage (115VAC) polarity reversed. If twinned, refer to...

Day + Night furnace blower only comes on with no heat [ 18 Answers ]

Hello and Happy New Year... We have about a 15 year old Day + Night furnace that only the blower comes on with no heat... Is there a way to test the limit switches? There is 4 of them in the furnace.. There is a small square button in the center of all of these switches.. I wanted to test these...

Furnace blower on, not heat [ 1 Answers ]

I have an Amana 880SSE furance. I couple nights ago all the CO detectors in the house went off & the furnace quit "heating" but blower stayed on. I went through normal "troubleshooting" & it started working normally. Last night the CO detectors did NOT go off, but the furnace again stopped...

Blower won't run in auto for heat with oil furnace [ 9 Answers ]

I have an oil furnace. A/C works fine. Heat last season worked fine. Started up furnace this year just fine. But blower would not start on auto. The blower will run in heat mode when set to On. I replaced the Limit Switch in the Plenum. No change.

Furnace Blower stays on, no heat [ 2 Answers ]

Hello, I have an older Bryant furnace model # 396gadd36075. I turned on the heat the other day and the no heat. I notice the unit had been turned off (pilot was not lit), apparently by the service company I use when they came to do the spring check for the AC. I followed the instructions to...

View more questions Search