Ask Experts Questions for FREE Help !
Ask
    dennyb123's Avatar
    dennyb123 Posts: 1, Reputation: 1
    New Member
    		  
    #1

    Oct 17, 2007, 07:37 PM
    Intertherm Furnace
    My furnace Intertherm Model # MHHB-077ABHR-06 just starteed kicking the blower in and out. The blower will run for 30 seconds, then stop, about 10 seconds later, it'll kick in again. Sometimes this will go on for 15 minutes. The flame is kicking in and it has electronic ignition.
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #2

    Oct 18, 2007, 04:07 PM
    Your blower motor fan control is probably defective. This control tells the blower to turn on when the heat in the furnace is high enough to allow the blower to turn on and stay running until the thermostat is satisfied.
    ctagaban's Avatar
    ctagaban Posts: 3, Reputation: 1
    New Member
    		  
    #3

    Oct 19, 2007, 09:06 PM
    I replaced the nozzle and oil filter and ever since then, nothing but problems, first there was too mcuh oil around the nozzle, fixed that but now when it ignites and starts up the flame it rumbles. The oil has ignited but runs really rough. I tried to adjust air flow but to no avail. What could be the problem?
    ctagaban's Avatar
    ctagaban Posts: 3, Reputation: 1
    New Member
    		  
    #4

    Oct 19, 2007, 09:11 PM
    I replaced the nozzle and oil filter on my Intertherm furnace and nothing but problems began. First there was too much oil coming from the nozzle, so I replace nozzle holder and igniters. Then I bled the air, lots of air, and it ignites but rumbles really bad, I adjusted the air flow but still does not run smoothly. What do I need to do to get it run properly?
    T-Top's Avatar
    T-Top Posts: 1,871, Reputation: 100
    Ultra Member
    		  
    #5

    Oct 19, 2007, 09:22 PM
    I agree with hcac1000 it may be a weak fan control switch or it may be that you have a dirty burner or burner orifice and it can not get the heat exchanger hot to keep the blower running.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

My intertherm furnace pilot lights but furnace won't kick on [ 5 Answers ]

I need some diagnostic help. We have a full propane tank. A new burner plate (last year) and the blower works. We light the pilot but the knob should pop up after one minute thus lighting the furnace. It won't pop up. What part should we replace? The furnace is a 17 year old Intertherm MGH...

Intertherm Furnace [ 2 Answers ]

I have an Intertherm Furnace model MGHA-077ABFC-05. The pilot continuously goes out on it. Is there another filter or something other than what is on the furnace door ?

Intertherm furnace [ 2 Answers ]

I have just in the last month had an Intertherm furnace installed, and since installation they have had to come in twice because they claim the starter button is not firing. They replaced it and now it is on the fritz again. It starts for about 8 seconds and cuts out. There is fuel in the tank....

Intertherm furnace [ 1 Answers ]

I own a 1985 modular home and the intertherm blower fan on my furnace quit working is it too hard to fix or change?:confused: Also what is the cost to fix it?:eek: Please help!! :) Thank you Rachell

View more questions Search