Ask Experts Questions for FREE Help !
Ask
    rr6's Avatar
    rr6 Posts: 25, Reputation: 1
    New Member
     
    #21

    Nov 22, 2013, 11:59 AM
    Hi Stan-40, I finally got back into the 100 amp main panel I'm pulling off for my 2-pole 50-amp feebdack main.

    In this 20 year old Square D box, the ground bus bar is isolated from the metal box by plastic. So I will leave my on the few neutrals that are there. I guess.

    I forgot to check and see if there is only 1 neural per hole on the neutral bar, from 20 years ago when I installed it. Probably is since I have not used on the breaker slots.

    I go the retaining g clip installed on the 2-pole feed-back main in the sub-panel. Thx again for that excellent tip!

    Another question if your still here, is the leads and neutral to sub-panel are #6 and I ran a #8 ground wire to the ground rod outside cabin for the sub-panel.

    Seems I recall two suggestions elswhere in my readings;

    1) I should use as large or larger than the leads, ground wire to the ground rod,

    2) I should have installed two ground rods?

    I put the ground rod in on 8 or 10ft ground rod in on a 45 degree slant and was short if getting it all the way in by about 2 or 2.5 ft.

    Also I installed the rod so that its actually under the house, so it may get less moisture from rain fall ergo less good grounding.

    Thx for any advice.
    Quote Originally Posted by stanfortyman View Post
    If there are neutrals actually on an add-on ground bar, screwed directly to the back of the panel box, I would definitely move them to a neutral bar.
    The panel box itself cannot be a path for neutral current.
    rr6's Avatar
    rr6 Posts: 25, Reputation: 1
    New Member
     
    #22

    Nov 22, 2013, 12:01 PM
    Hi Stan-40, I finally got back into the 100 amp main panel I'm pulling off for my 2-pole 50-amp feebdack main.

    In this 20 year old Square D box, the ground bus bar is isolated from the metal box by plastic. So I will leave my on the few neutrals that are there. I guess.

    I forgot to check and see if there is only 1 neural per hole on the neutral bar, from 20 years ago when I installed it. Probably is since I have not used on the breaker slots.

    I go the retaining g clip installed on the 2-pole feed-back main in the sub-panel. Thx again for that excellent tip!

    Another question if your still here, is the leads and neutral to sub-panel are #6 and I ran a #8 ground wire to the ground rod outside cabin for the sub-panel.

    Seems I recall two suggestions elswhere in my readings;

    1) I should use as large or larger than the leads, ground wire to the ground rod,

    2) I should have installed two ground rods?

    I put the ground rod in on 8 or 10ft in on a 45 degree slant and was short if getting it all the way in by about 2 or 2.5 ft.

    Also I installed the rod so that its actually in ground under the cabin, so it may get less moisture from rain fall ergo less good grounding.

    Thx for any advice. Next I figure reepticles, wiring lighting.
    Quote Originally Posted by stanfortyman View Post
    If there are neutrals actually on an add-on ground bar, screwed directly to the back of the panel box, I would definitely move them to a neutral bar.
    The panel box itself cannot be a path for neutral current.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Can I replace a fat 15 amp breaker with a skinny 15 amp breaker [ 3 Answers ]

I have a Siemens I-T-E panel and need to make room for a double 30 amp circuit breaker for my generator. Unfortunately, I'm out of space in the panel box to add the extra breaker. I have a lot of "fat" 15 amp breakers and I was wondering if I could replace four "fat' breakers with four "skinny"...

Can I downgrade a 200 amp service with a 200 amp main by adding a 100 amp breaker to [ 1 Answers ]

Can I downgrade a 200 amp service to a 100 amp service by adding a 100 amp breaker to the panel

Can I tapinto the line side of a100 amp main breaker to feed a 60 amp breaker service [ 1 Answers ]

Can I tap into the line side of a 100 amp main breaker to feed a 60 amp breaker for a electric stove


View more questions Search