Ask Experts Questions for FREE Help !
Ask
    cptcrump's Avatar
    cptcrump Posts: 9, Reputation: 1
    New Member
     
    #1

    Aug 6, 2014, 10:23 AM
    What causes drywall to crack near the corners of doors and windows?
    The house is two story wood frame built in 2001 in Northern California.
    smoothy's Avatar
    smoothy Posts: 25,490, Reputation: 2853
    Uber Member
     
    #2

    Aug 6, 2014, 11:08 AM
    Usually it has to do with humidity swings.. the sheetrock contracts slightly when it gets really dry. I have the same issues in Virginia in a house built in the early 60's. If I don't run a humidifier in winter due to natural gas heat.
    ma0641's Avatar
    ma0641 Posts: 15,675, Reputation: 1012
    Uber Member
     
    #3

    Aug 6, 2014, 11:17 AM
    Weather changes and settlement. How big(wide) and long are they. Post a picture if possible.
    cptcrump's Avatar
    cptcrump Posts: 9, Reputation: 1
    New Member
     
    #4

    Aug 31, 2014, 10:59 AM
    Quote Originally Posted by smoothy View Post
    Usually it has to do with humidity swings.. the sheetrock contracts slightly when it gets really dry. I have the same issues in Virginia in a house built in the early 60's. If I don't run a humidifier in winter due to natural gas heat.
    Thanks, I'll look into that although the climate here is pretty dry year round. We haven't noticed when the cracks form so perhaps we can monitor that.
    joypulv's Avatar
    joypulv Posts: 21,591, Reputation: 2941
    current pert
     
    #5

    Aug 31, 2014, 11:20 AM
    So many variables. Framing wasn't dry, or house was built during a very humid time. Poor roof construction, or cellar floor sinking, or any number of such things. Have you gone over the entire house top to bottom, inside and out?
    cptcrump's Avatar
    cptcrump Posts: 9, Reputation: 1
    New Member
     
    #6

    Aug 31, 2014, 11:29 AM
    Quote Originally Posted by ma0641 View Post
    Weather changes and settlement. How big(wide) and long are they. Post a picture if possible.
    They vary from about 6 to 12 inches long. Here are the worst.
    Attached Images
         
    cptcrump's Avatar
    cptcrump Posts: 9, Reputation: 1
    New Member
     
    #7

    Aug 31, 2014, 11:35 AM
    Quote Originally Posted by joypulv View Post
    So many variables. Framing wasn't dry, or house was built during a very humid time. Poor roof construction, or cellar floor sinking, or any number of such things. Have you gone over the entire house top to bottom, inside and out?
    Yes, there are no other signs of settlement or foundation cracking. House is essentially on rock at 1300 feet elevation on a hillside. Some cracks are on exterior walls on east side, some on an interior wall.
    joypulv's Avatar
    joypulv Posts: 21,591, Reputation: 2941
    current pert
     
    #8

    Aug 31, 2014, 11:57 AM
    Is that textured paint or textured skimcoat? How far in can you get a toothpick?
    cptcrump's Avatar
    cptcrump Posts: 9, Reputation: 1
    New Member
     
    #9

    Aug 31, 2014, 12:51 PM
    Quote Originally Posted by joypulv View Post
    Is that textured paint or textured skimcoat? How far in can you get a toothpick?
    It's skimcoat. Worst case is 1/8 inch or less. Most seem to go no deeper than the paint, skimcoat, and maybe the paper on the drywall.
    ma0641's Avatar
    ma0641 Posts: 15,675, Reputation: 1012
    Uber Member
     
    #10

    Aug 31, 2014, 01:33 PM
    That is a pretty typical picture of wall shifting, the house is racking slightly. If the doors are able to open and close properly, use a good grade of siliconized acrylic caulk and fill them in.
    joypulv's Avatar
    joypulv Posts: 21,591, Reputation: 2941
    current pert
     
    #11

    Aug 31, 2014, 02:56 PM
    Doesn't sound serious, not going through the skimcoat.
    Half pint of latex reinforced plaster repair and a putty knife.
    cptcrump's Avatar
    cptcrump Posts: 9, Reputation: 1
    New Member
     
    #12

    Aug 31, 2014, 04:39 PM
    Quote Originally Posted by joypulv View Post
    Doesn't sound serious, not going through the skimcoat.
    Half pint of latex reinforced plaster repair and a putty knife.
    Thanks, I'll try that.

    Quote Originally Posted by ma0641 View Post
    That is a pretty typical picture of wall shifting, the house is racking slightly. If the doors are able to open and close properly, use a good grade of siliconized acrylic caulk and fill them in.
    Thanks.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Why does my paint crack in the corners and edges after painting [ 2 Answers ]

I have caulked all the edges of the room as was cracking I have then used Dulux emulsion on the wall and the paint has cracked really badly on every edge and corner what am I doing wrong this is in every room.

Vertical drywall crack over archway [ 1 Answers ]

4' long vertical crack in drywall starting at the centerline of a archway, from top of archway to bottom of ceiling 4' long. This area is the vertical face of a vaulted truss set 20' wide. Trusses sit on bearing wall at this point also. Crack is on a truss kingpost that is attached to a 2ply 2x10...

Joint compound cracks on inside corners of drywall [ 4 Answers ]

I'm finishing drywall and am having a problem with the inside corners... I used the 90 minute Sheetrock Lightweight Setting-Type Joing Compound powder to embed the tape everywhere... all that worked great... However, I'm finishing with Sheetrock Lightweight All Purpose Joint Compound (blue...

Windows and doors [ 1 Answers ]

Does anyone have any input on comparing Silverline windows and Jeldwin windows? How does each of them rate? ALso, compare Millikin patio doors vs. Jeldwin doors. Thanks Stephanie


View more questions Search