Ask Experts Questions for FREE Help !
Ask
    unit 5207's Avatar
    unit 5207 Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Jun 13, 2009, 02:34 PM
    no cold air
    I had a white-rodgers thermostat 1f58w-58. I switched it to a hunter 44860, and it only blows heat its hooked as y1=yellow,y2=brown,w2=black,g=green,r=rh,rc/r=pink,c=blue,w1=white. Where did I go wrong?
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #2

    Jun 13, 2009, 03:02 PM
    Exactly how was the old thermostat wired. I hope you kept a copy of the terminal designations you wrote down before the start of the project as instructed in the install instructions. Many times the color code does not match the standard wiring color code because some installers follow there own little wiring code setup.
    unit 5207's Avatar
    unit 5207 Posts: 2, Reputation: 1
    New Member
    		  
    #3

    Jun 13, 2009, 03:16 PM
    Quote Originally Posted by hvac1000 View Post
    Exactly how was the old thermostat wired. I hope you kept a copy of the terminal designations you wrote down before the start of the project as instructed in the install instructions. many times the color code does not match the standard wiring color code because some installers follow there own little wiring code setup.
    Don't know how the old one was installed guess I'm up a creek, wife tried installing it before I got home. And told me to finish. Thought that's the only way I would start it. Is there any thing I can do?
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #4

    Jun 13, 2009, 06:14 PM
    http://www.white-rodgers.com/wrdhom/.../0037-3926.pdf


    http://www.white-rodgers.com/wrdhom/..._06_pg0192.pdf


    These are wiring diagrams for your old WR stat
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Why cold air blows out of cold air return when furnace is on [ 1 Answers ]

Why does cold air blow out of the cold air return when the furance is on?

Cold and drafty from ceiling mounted cold air return [ 1 Answers ]

I recently purchased a adobe style home built in 2000 with a Single Roof Mounted combined HVAC system in the Albuquerque New Mexico Area. Directly below the HVAC is the only cold air return duct work located in the ceiling of the Hallway on one end of the Home. A single Thermostat for the entire...

Cold Snowblower great, cold dies [ 2 Answers ]

I have an old Tech engine snowblower and it starts great and everything , but recently it has started acting-up it lacks power and dies when warmed-up please help:confused:

Furnace blowing cold air.starts out warm, goes to cold. [ 6 Answers ]

Hoping for help here. I recently had my ignitor replaced. Before that, the furnace wasn't working at all. Now it starts blowing warm (not hot) air, then gradually over a period of a couple of hours, the air cools down until it is completely cold and the temperature in the house drops drastically....

New mains shower, reasonably new Combi-boiler, but hot-cold-hot-cold-hot-cold shower! [ 4 Answers ]

I've recently had a new bathroom put in, with a mains shower (used to be electric). But now my shower keeps running hot-cold-hot-cold every minute or so. My bath tap and sink tap in the bathroom are running fine, it's just the shower. I was told this shouldn't happen as I have a combi-boiler but...

View more questions Search