Ask Experts Questions for FREE Help !
Ask
    daveinbldr's Avatar
    daveinbldr Posts: 1, Reputation: 1
    New Member
     
    #1

    Feb 26, 2008, 06:05 PM
    Cast Iron Drain Pipe
    I would like an answer to several questions.

    1. I have a rough-in for a shower in my basement. The concrete floor has a 7" diameter hole with a cast iron pipe about 9" down from the concrete surface. There is a round plug in the end of the cast iron with no square in the center for a wrench. There appears to be lead
    Around the outside of the plug. How do I remove the plug?

    2. Once the plug is out, can I assume that there is a trap in place as part of the rough-in? The house is 40 yrs old.

    3. What is the best way to tie in a PVC pipe to the cast iron? And do I need to back fill in around the drain pipe to support it. Like I said, 7" x 9" deep. I'm putting in a Swanstone base.

    Thanks,

    Dave
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
     
    #2

    Feb 26, 2008, 06:20 PM
    No you should assume there is no trap at this point until you get the plug removed and test for a trap. 40 years ago you don't know if they roughed for a toilet, shower or a tub, its just a 4Z"pipe for now. Your Swanstone shower will have a drain opening that accepts a 2"PVC pipe held by a fat black collar, kind of like a rubber ribbed ring. You'll have 2"PVC coming out of the shower and your need to weld tohether a PVC trap. The trick will be getting that 2"PVC to adapt to the cast iron pipe that is held by lead and Oakum. To remove the old cap you should drill 3/8" holes in the lead about every half inch all the way around the cap. Now drive a screw driver point into the lead and start prying, it will peel out and you will see the Oakum. You can pick at the Oakum with needle nose plyer, I have a big fish hook that is straightened into a mini spear, works great.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Replacing cast iron drain pipe? [ 6 Answers ]

Put in a dishwasher and was working on the drain when I noticed the 2" cast iron drain pipe wasnt in very good shape. I spliced it with a sawzall ans the put pvc in and tried to use a boot on each end but it still leaks. Then from the cutting another joint in it started to leak. Ive decided its...

Shower drain connection with cast iron pipe [ 7 Answers ]

We have a cast iron shower drain pipe in a concrete floor. It is a shower on a slab. We are building a shower pan with tiles or pebbles as a finish. We have purchased drain but it is not working - it is for premade shower enclosures. We need some kind of adapter to connect cast iron pipe with PVC...

Crooked cast iron drain pipe [ 1 Answers ]

I have a shower unit in the basement which began leaking when I started using it last year. I tried replacing the drain but that only stopped the leaking for a few weeks. It leaks steadily when in use, under the shower base, under the studs and into the laundry room. The entire shower unit was...

Washing machine drain pipe overflows -- cast iron? [ 1 Answers ]

Our washing machine drain overflows each time the machine drains -- I have snaked, used a pressure cuff with the garden hose, and tried Drano. The drain pipe is cast iron from the 1950s -- I'm wondering whether it has just corroded inside to the point that the internal diameter is partially...

PVC or Cast Iron Drain Pipe [ 2 Answers ]

My Drain Pipe outside the house has been damaged severely by tree roots. Will it be better to replace it wit PVC or Cast Iron? What are the advantages and Disadvantages of using Cast Iron?


View more questions Search