Ask Experts Questions for FREE Help !
Ask
    SEETARM's Avatar
    SEETARM Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Nov 26, 2007, 11:30 AM
    Honeywell Magicstat 32 Model CT3200
    Help:

    The reading on my CT3200 is higher from the room temperature by at least 2 degrees Celsius during the heating season. I measured the temperature with a digital thermometer which read 20 degrees Celsius and my CT3200 was reading 22 degrees Celsius. It's on an inside wall which is well insulated with no drafts.

    How do I get the correct reading on my CT3200?
    rtw_travel's Avatar
    rtw_travel Posts: 347, Reputation: 36
    Full Member
    		  
    #2

    Nov 26, 2007, 11:41 AM
    There may be no drafts in the room, but have you checked to ensure there are no drafts coming through the wall where the wires attach to the thermostat? Maybe plug the hole with insulation or what-have-you. It doesn't take much of a draft there to make a difference.

    If this doesn't solve the problem there there are only two options: 1) replace the thermostat (perhaps call Honeywell for a warranty replacement?) or 2) turn your heat down to compensate for the inaccuracy. There is no way that I am aware of to re-calibrate a digital thermostat.
    jbsimpson's Avatar
    jbsimpson Posts: 2, Reputation: 1
    New Member
    		  
    #3

    Feb 3, 2010, 08:47 AM

    I have a magicstat/32 and I want to operate a hot water unit heater is it possible to run furnace and fan for heater on this thermostat/
    wmproop's Avatar
    wmproop Posts: 3,749, Reputation: 91
    Ultra Member
    		  
    #4

    Feb 3, 2010, 03:37 PM
    Quote Originally Posted by jbsimpson View Post
    i have a magicstat/32 and i want to operate a hot water unit heater is it possible to run furnace and fan for heater on this thermostat/


    The thread you put this in want get read by many people,, its 3 months old,, you need to start your own thread
    jbsimpson's Avatar
    jbsimpson Posts: 2, Reputation: 1
    New Member
    		  
    #5

    Feb 4, 2010, 05:00 AM
    I have thermastst magicstat/32 will it operate furnace and a fan.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Honeywell CT3200 - fan continuously running [ 2 Answers ]

I just noticed that regardless of whether the FAN switch is in the AUTO or ON position, the fan is continuously running. It just started to do this, this past week, up until now it was fine, only running when the furnace kicked in. When I turn the SYSTEM switch from HEAT or COOL to OFF, it...

Honeywell MagicStat 32 - Model CT3200 [ 9 Answers ]

Hi, I have a Honeywell Thermostat MagicStat/32 which is saying (not Flashing) "bat low." As per the instruction manual, I changed the Batteries. This did not clear the screen. I tried another set of new Batteries, which again did not clear the screen. I am sure I put them In correctly. ...

Honeywell MagicStat 32 - Model CT3200 [ 2 Answers ]

Hi, I have a Honeywell Thermostat MagicStat/32 which is saying (not Flashing) "bat low." As per the instruction manual, I changed the Batteries. This did not clear the screen. I tried another set of new Batteries, which again did not clear the screen. I am sure I put them In correctly. ...

Honeywell CT3200 for Fireplace [ 1 Answers ]

I've replaced the CT3200 that came with the house with a newer thermostate. Now the simple spring thermostat from the gas fireplace just quit. Can I use the 3200 to simply turn the fireplace on and of at a given time? There is only a black and white wire coming out of the wall and W Y G and R...

Honeywell thermostat - model RTH230B [ 1 Answers ]

I need directions how to program this thermostat.

View more questions Search