Ask Experts Questions for FREE Help !
Ask
    NYCBronx's Avatar
    NYCBronx Posts: 5, Reputation: 1
    New Member
    		  
    #1

    Sep 1, 2007, 07:30 AM
    Kenmore Model 41741042000 (Front door) Washing Machine
    I recently had a flood in my basement and my Kenmore Washing Machine Model # 41741042000 was damaged. The problem with my Kenmore is that when you turn the power on it does not response to any of the settings. In other words, it does not work when turned on. I believe the problem is a computer malfunction? If any one knows the part(s) needed and how to fixthis problem that would be very useful. Thanks.
    esquire1's Avatar
    esquire1 Posts: 2,483, Reputation: 209
    Ultra Member
    		  
    #2

    Sep 1, 2007, 07:44 AM
    Did you check your breakers? Do you have power to the outlet? I would first check all the eletrical wires and connections on the washing machine. . Did the water get so high that it got into the circuit board?
    NYCBronx's Avatar
    NYCBronx Posts: 5, Reputation: 1
    New Member
    		  
    #3

    Sep 1, 2007, 07:52 AM
    Yes, the circuit board was damaged located on the bottom front of the machine.
    NYCBronx's Avatar
    NYCBronx Posts: 5, Reputation: 1
    New Member
    		  
    #4

    Sep 1, 2007, 07:59 AM
    An addition, the machine takes water but doesn't take it. Does however drain it. So its not the water pump.
    NYCBronx's Avatar
    NYCBronx Posts: 5, Reputation: 1
    New Member
    		  
    #5

    Sep 1, 2007, 08:00 AM
    Not take (typo) turn it
    esquire1's Avatar
    esquire1 Posts: 2,483, Reputation: 209
    Ultra Member
    		  
    #6

    Sep 1, 2007, 08:06 AM
    The circuit board is shot if if got water on it. Will your insurance cover this?
    NYCBronx's Avatar
    NYCBronx Posts: 5, Reputation: 1
    New Member
    		  
    #7

    Sep 1, 2007, 08:13 AM
    No the insurance does not cover the washer. It is almost 8 years old. I am just trying not to pay a lot to a repairman. I would rather buy a new one if it will cost a lot. Do You think it's the circuit board? How much does one of them cost? Is it easy to install? Thanks a lot for your help!
    esquire1's Avatar
    esquire1 Posts: 2,483, Reputation: 209
    Ultra Member
    		  
    #8

    Sep 1, 2007, 08:31 AM
    It is easy to change. Go to Appliance Parts from RepairClinic.com - HomePage or ApplianceJunk.com - Appliance Repair Forums - How to Videos for pricing. I'm guessing $150-$175 for the part. Yes, you must weigh the options of cost vs new unit. Good Luck
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Kenmore Elite Calypso Washing Machine, Model number 110.2206 [ 4 Answers ]

Would you please help me with the following issue? My washer is not draining, nor is it spinning. There is a lot of water collected at the bottom and I can't drain or spin? I try to restart it and it just beeps and rumbles for a couple seconds and then stops. Thank you so much in advance for...

Kenmore washing machine model #23822100 Will not drain [ 2 Answers ]

Hello, I was 3 minutes into a the washing cycle and it was making a sound like it was out of balance. I lifted the lid, adjusted the towels and shut the lid. It will not start. Not on any setting. It will click when I turn the dial like it wants to chance cycles, but nothing happens. Now, I...

Kenmore Washing machine model 110. 84870810 [ 2 Answers ]

My machine stop spinning.. and draining I have no maunal:( :( :confused: :confused:

Kenmore Model 41741042000 Not Draining Fully [ 2 Answers ]

I have a Kenmore Model 41741042000 front loader that is not draining the water fully leaving approximately 3" of water in the tub. There is also a strong odor. Does this problem require a service call or is there a relatively procedure I could do such as cleaning a filter or something like that?...

Kenmore Washing Machine Model 110.26722690 [ 3 Answers ]

I have an ~1996 Kenmore washing machine. The motor coupling needs to be replaced, but prior to replacing it I noticed that the bottom agitator will not move in either direction. What do I need to do to trouble shoot this problem? Thanks for your help!

View more questions Search