Ask Experts Questions for FREE Help !
Ask
    techtimdavis's Avatar
    techtimdavis Posts: 103, Reputation: 1
    Junior Member
     
    #1

    Nov 2, 2017, 11:22 AM
    My remote start isn't working correctly.
    The remote start on my 2008 Chrysler Town and Country Touring Edition isn't working correctly. I press twice on the button on the key fob, the van starts for a few seconds then shuts off. This feature is very handy in the winter time. What should I look at first to diagnose this issue. It worked fine last winter.
    talaniman's Avatar
    talaniman Posts: 54,325, Reputation: 10855
    Expert
     
    #2

    Nov 2, 2017, 01:08 PM
    Does the same thing happen when you start it manually?
    techtimdavis's Avatar
    techtimdavis Posts: 103, Reputation: 1
    Junior Member
     
    #3

    Nov 2, 2017, 01:13 PM
    No it runs and drives normally if I start the vehicle with the key.
    talaniman's Avatar
    talaniman Posts: 54,325, Reputation: 10855
    Expert
     
    #4

    Nov 2, 2017, 01:52 PM
    Maybe you need a fresh battery in the remote, which any dealer can change, maybe auto zone or places like it, or try it yourself. Check out these videos.

    https://www.youtube.com/watch?v=KzCXGXCe0oc

    Or check the subsequent videos that also show worn out buttons, or just replace the remote and program it.

    Disconnecting the positive battery cable for 60 seconds resets the system as a last resort, but weak batteries should be changed.
    ma0641's Avatar
    ma0641 Posts: 15,675, Reputation: 1012
    Uber Member
     
    #5

    Nov 2, 2017, 02:02 PM
    I'd start with battery change in the remote.
    techtimdavis's Avatar
    techtimdavis Posts: 103, Reputation: 1
    Junior Member
     
    #6

    Nov 16, 2017, 04:55 PM
    The batteries in the remotes are good, when I press the remote start button twice, the van will start run for less than a minute then shut off.
    ma0641's Avatar
    ma0641 Posts: 15,675, Reputation: 1012
    Uber Member
     
    #7

    Nov 17, 2017, 07:14 AM
    Is the engine light on? Is there a security system on this car?
    techtimdavis's Avatar
    techtimdavis Posts: 103, Reputation: 1
    Junior Member
     
    #8

    Nov 17, 2017, 07:19 AM
    The check engine light is on, and yes there is a factory installed security system.
    talaniman's Avatar
    talaniman Posts: 54,325, Reputation: 10855
    Expert
     
    #9

    Nov 17, 2017, 07:33 AM
    You should find out what that CHECK ENGINE is about. Had any work done lately on this vehicle?
    techtimdavis's Avatar
    techtimdavis Posts: 103, Reputation: 1
    Junior Member
     
    #10

    Nov 17, 2017, 07:35 AM
    Ok, I'll get the CEL looked at, it was in the body shop for front end work after my wife hit a deer with it last winter.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

How to determine if your ceiling fan and remote is wired correctly [ 0 Answers ]

How to determine if your ceiling fan and remote is wired correctly. Can the blue wire be connected to the black receiver wire. Will that work

Gas Heater not working correctly [ 3 Answers ]

After reading the guide I believe it may be overheating. The digital thermostat will go blank after running for 10 min or so and the display will turn back on in about 20min. The system is not able to keep the house over 60F. I don't think it has been cleaned in the 4 years I've lived there...

4 way not working correctly [ 10 Answers ]

Purchased a house and the 4 way not working. Figured that someone miswired one of the switches and when I checked the boxes this is what I found. Box 1 at bottom of stairs has 14-3 and 12 -2 BX cable. Power into this box. What is confusing in this box is that someone attached a bare copper wire...

How do I correctly wire a new ceiling fan (with a remote) when there are 2 switches? [ 9 Answers ]

I am trying to replace an old ceiling fan (that had a light) with a newer version that has a remote to control both the light and fan. The old fan was wired to work on 2 separate switches - one for the light (I'll call it switch #1) and one for the fan (switch #2). There is a third switch in the...

Furnace not working correctly [ 1 Answers ]

My furnace kicks on and off like everything is okay but it blows cold air. I took the cover off and it has an automatic pilot but it is not coming on. Any suggestions?


View more questions Search