Ask Experts Questions for FREE Help !
Ask
    pastor1189's Avatar
    pastor1189 Posts: 1,538, Reputation: 3
    Ultra Member
    		  
    #1

    Sep 29, 2013, 05:06 AM
    Fascia Board Replaced
    Fascia Board Replaced. I took the measurements. 68" long, 7" wide
    3/4 " thick. I just hope I do not have to rip the board. Cross cut is no problem. I wonder what the best size is and is available?
    ma0641's Avatar
    ma0641 Posts: 15,675, Reputation: 1012
    Uber Member
    		  
    #2

    Sep 29, 2013, 05:26 AM
    1x6, 6 ft long. 1x6 is 7 1/8 to 7 1/4 and should be what you have as it is a common size.
    pastor1189's Avatar
    pastor1189 Posts: 1,538, Reputation: 3
    Ultra Member
    		  
    #3

    Sep 29, 2013, 05:34 AM
    Very Good
    joypulv's Avatar
    joypulv Posts: 21,591, Reputation: 2941
    current pert
    		  
    #4

    Sep 29, 2013, 06:37 AM
    1 x 6? Don't you mean 1 x 8?
    It would have to be ripped. Attach a small length of wood onto the board as a straight edge. Two little nails would hold it enough for a circular saw.
    creahands's Avatar
    creahands Posts: 2,854, Reputation: 195
    Ultra Member
    		  
    #5

    Sep 29, 2013, 08:32 AM
    joy is right. It would be a 1 x 8.

    Cut the length you need and check to see if it is longer in width then existing fascia. It very likely is the same size.

    Chuck
    ma0641's Avatar
    ma0641 Posts: 15,675, Reputation: 1012
    Uber Member
    		  
    #6

    Sep 29, 2013, 09:22 AM
    Quote Originally Posted by joypulv View Post
    1 x 6? Don't you mean 1 x 8?
    It would have to be ripped. Attach a small length of wood onto the board as a straight edge. Two little nails would hold it enough for a circular saw.
    DUH 1X8 is correct. May not have to rip depending on roof edge. Builders like to use a std. size and not rip. Sometimes they will cut a bevel at the top to match the roof slope.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search


Check out some similar questions!

Blower motor on constant, board replaced, all sw's closed [ 2 Answers ]

We had a power outage, and, after power was restored, my blower motor was running constantly. I replaced the controller board, still same. I checked all limit switches I could find, and all were closed, opening did nothing to keep the blower from running. I checked the safety fusible link, from...

Have a blower motor that still will not come on even after replaced with a new board. [ 0 Answers ]

Have an electric furnace; have replaced new control board and fan for blower will not come on when set in auto or on position. Have the blower motor straight wired now and blower works perfect; blowing good heat; any ideas?

Replaced board and no status light [ 1 Answers ]

I have a goodman b18099-06 board fried when the draft reducer motor went out so I got new board wired it all up and doesn't even work no status light at all

Recently replaced furnace control board, now blower will not come on with AC. [ 3 Answers ]

I recently replaced a 50A50-110 control board (Comfortmaker) with a White-Rodgers universal 50M56U-843 control board and the furnace worked fine throughout the winter. However, I just tried the AC for the first time this season and the blower will not come on with the AC. The compressor and outside...

View more questions Search