Ask Experts Questions for FREE Help !
Ask
    Jofawan's Avatar
    Jofawan Posts: 1, Reputation: 1
    New Member
     
    #1

    Aug 14, 2012, 11:27 AM
    Control arm bushings; replace both?
    The dealer (on a recall for airbag visit) told me my control arm bushings are broken (lower); should I replace both upper and lower, since the work on the lower will be done anyway?

    And can you tell me if I can confirm them being broken myself, just by removing the tire. Same for the ball joints; how can I tell if I need them too?

    Tnx
    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #2

    Aug 14, 2012, 11:41 AM
    Year, Make, Model, and Mileage?

    If you have over 125,000 miles on a front wheel drive vehicle, such as a Honda, the most important of those parts to replace are the ball joints. It's catastrophic is one fails--the whole front wheel, steering knuckle, and half-axle will be ripped off. Go with Moog ball joints; they will make a huge difference that you will be able to notice.

    As a generalization, I would replace both lower and upper bushings.
    smoothy's Avatar
    smoothy Posts: 25,490, Reputation: 2853
    Uber Member
     
    #3

    Aug 14, 2012, 11:43 AM
    Personally I would... only because I am that sort of person... however you don't generally HAVE to do it. Uppers and lowers don't always wear at the same rate on a particular car. As TXGreaseMonkey asked what car is it.

    And example being Older Mercedes Benzes... you will usually go through several upper bushings without ever doing a lower... and thank goodness because the uppers are quick and easy and the lowers are very labor intensive.

    I would however do always both sides in a repair as a matter of safety and principle.

    There are ways to check for this however they are easy to describe, but difficult to judge in practice without experience doing it.

    Its all a matter of yanking, pulling shaking and leveraging... and knowing what's normal by sense of feel, and being aware of what else is going on... namely some of them are going to affect the steering column and there is movement there that will be normal to a certain extent.

    If you have a concern it might be worth taking to a second mechanic to get a second opinion.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

How do I replace a shower arm? [ 4 Answers ]

I have a 19 year old home with antique brass finish fixtures that I'd like to update to chrome. I have tried to change out the ancient, yellowed plastic handheld shower (broken handle and hose not long enough) however the shower arm has a ball at the end which will not release to allow me to...

Trailing arm bushings [ 0 Answers ]

1990 honda civic DX. I am replacing the trailing arm bushings (rear suspension). The replacment bushings have the 2 hole metal plate already in them. Question: how do I press in the new bushings and should they be glued? Also, how are the rear tires "aligned" after re-installation of the...

Replace PVC P-Trap and Waste Arm with Brass/Chrome [ 9 Answers ]

How do I replace PVC p-trap and waste arm with chrome/brass one for a decorative drain to complement a pedestal sink? The PVC is screwed to the metal (galvnaized steel?) stub out at the wall. I would like the new p-trap and waste arm to be adjustable in/out to allow for the new drain location of...

Control arm bushings on a lexus [ 1 Answers ]

Could someone please tell me how to change the control arm bushings on my 93 lexus es300 I have the bushings and I tried to change them but I couldn't get them to come out. Do I need a special tool or something? Any help would be greatly appreciated.

Replace Honda turn signal arm [ 1 Answers ]

How do you get to the turn signal arm to replace it?


View more questions Search