Ask Experts Questions for FREE Help !
Ask
    DrewB's Avatar
    DrewB Posts: 2, Reputation: 1
    New Member
     
    #1

    Dec 4, 2011, 12:16 PM
    I have a Kenmore Smart Heat Quiet Pak 4 model; 110.97872601
    Was working fine then a code of P70 came up after 3 beeps? How do I figure this out and fix it?
    drtom4444's Avatar
    drtom4444 Posts: 3,282, Reputation: 145
    Ultra Member
     
    #2

    Dec 5, 2011, 01:22 AM
    It's dirty and you need to tear it down and clean it.
    DrewB's Avatar
    DrewB Posts: 2, Reputation: 1
    New Member
     
    #3

    Dec 5, 2011, 08:26 AM
    We clean the lint vent before every load. I have cleaned out the lint vent exiting the house, but have not pulled the dryer out and cleaned it fro that point. Is that what you are talking about?

    Thanks for the help, more than you know.
    drtom4444's Avatar
    drtom4444 Posts: 3,282, Reputation: 145
    Ultra Member
     
    #4

    Dec 5, 2011, 12:47 PM
    You will have to clean the drier out thoroughly; just doing what you said does not prevent the lint build-up. You probably have about a five gallon bucket of dirt lining the air ducts. Every air duct will have to be removed and scraped and washed out to remove baked on lint deposits which is like concrete lining. This will burn so the manufacturer has installed the safeties to keep from having a house fire. Driers were the number one cause of fires at one time. Look at: http://www.youtube.com/watch?v=MMP7BW1lLs4 to see how. Also: http://www.youtube.com/watch?v=iBiRw-KElC4 ; http://www.youtube.com/watch?v=yFTZGgVisCI
    When you finish cleaning the drier it is best to also replace the belt, too, because you do not want to have to disassemble it again, and if the belt is over two years old you should replace it.

    Note that on most of the videos it does not show them washing out the parts, but this is important because it's the only way to really get the parts clean, just don't get motor wet or the capacitor if it has one. Vacuum out motor. I would move the drier out to your garage to have plenty of space to work. You also want to check your vent and clean it, also. The job is really easier than it sounds. There is no shortcut that will work; it has to be cleaned well. Before you re-assemble it make sure to use white lithium grease (high-temp grease) and grease all bearings. Just vacuuming out the dryer a little does little good. You also want to check the vent and clean it out. When you are done you will have a new dryer and it will dry like new again. You want to clean it like this every two years or every year with many children. DrTom4444

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Kenmore Quiet Pak 4 [ 4 Answers ]

Machine dispenses bleach and fabric softener immediately when deposited in the machine. It then ruins any clothing it comes in contact with as it has not diluted with water yet. What is wrong?

My Kenmore Elite Smart Heat Quiet Pak 9 HE4 will not start When I press the start bu [ 0 Answers ]

My Kenmore Elite Smart Heat Quiet Pak 9 HE4 will not start When I press the start button it just beeps

I have a 5 year old kenmore 90 series quiet pak 1 heavy duty dryer w/ heat issues [ 0 Answers ]

I have a 5 year old kenmore 90 series quiet pak 1 heavy duty dryer that occasionally fires up (which I can see) but more often than not is not firing. A slight grinding sound can be heard at the moment of failure to fire, and one can see at this point a little glowing at bottom. Thank you

Pictures of the inside of the kenmore dryer elite smart heat quiet pak 9 he4 [ 1 Answers ]

And directions because my dryer doesn't produce heat so I can't dry my clothes


View more questions Search