Ask Experts Questions for FREE Help !
Ask
    Husky21's Avatar
    Husky21 Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Jan 15, 2011, 09:22 AM
    Location of the OBD-II Plug in a 1995 Honda EX model.
    OBD-II Plug on the 1995 Honda EX model.
    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
    		  
    #2

    Jan 15, 2011, 09:33 AM

    Your Honda is OBD-I. OBD-II started in 1996. Here's how you can locate the Service Check Connector (SCC) on your car:

    https://www.askmehelpdesk.com/cars-t...tml#post832012
    Husky21's Avatar
    Husky21 Posts: 2, Reputation: 1
    New Member
    		  
    #3

    Jan 15, 2011, 10:51 AM
    Comment on TxGreaseMonkey's post
    TxGreaseMonkey thanks for clearing up the ODB-1 & ODB-2 question. Your link brings me to a page titled FAQ: How to Troubleshoot, Repair & Maintain Hondas and Selected Other Vehicles. I am not seeing your response on where the connector is located.
    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
    		  
    #4

    Jan 15, 2011, 12:00 PM

    5. Service Check Connector (SCC): Reading OBD-I Codes

    When the Check Engine Light (CEL) is on, it will be necessary to locate the 2-pin Service Check Connector (SCC) on OBD-I (pre-1996) Hondas. It is normally located under the dash, approximately 1 inch (2.5 cm) from the right kick panel. Take a small screwdriver and carefully pry it from the rubber mount. The other 3-pin connector in the rubber mount is the Data Link Connector (DLC), which should be left alone. Jump the SCC with a paper clip, turn the ignition switch to ON (Position II), and count the number of times, if any, the CEL flashes. Reference a Diagnostic Trouble Code (DTC) chart to identify the code being displayed. The SCC is also jumped, when an induction timing light is used to check engine timing.

    After troubleshooting, turn the ignition switch OFF, remove the jumper wire, and reset the ECM, by removing the BACK UP (7.5 A) fuse from the under-hood fuse box for 10 seconds. Disconnecting the BACK UP fuse cancels preset radio stations and the clock setting; therefore, they will need to be reset.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

94 honda civic obd location [ 8 Answers ]

Yes, I have a 1994 Honda Civic Ex Coupe. The engine code is D16Z6, it's a 1.6L Vtec Motor. Yesterday my check engine light came on. It's the first time this has ever happened since I owned the car. I have had the car since 2000, and have taken excellent care of it. I was wondering if you knew...

1992 Honda Civic - Can you interpret OBD-1 error codes? [ 1 Answers ]

The check engine light on my 1992 Honda Civic DX recently came on. When I turned the car off and on again, it was off and only came on after a minute or so. So I thought it was an emissions issue. Anyway, I checked the ECU error codes and got the following: 9 - CYP, cylinder sensor, 17 - VSS,...

Obd plug doesn't read [ 3 Answers ]

On a 2000 Accord coupe the OBD plug is not working properly. The emissions control people say they get no reading, and Advance Auto Parts said they got no reading when they plug in their meter. How can we trace down the problem?

Spark Plug Issues: 1995 Honda Civic [ 2 Answers ]

Hi, I had car trouble which made me think I need new spark plugs. (losing power erratically) Went to change them, one of the cylinders had a lot of oil in it when I took one plug out. Replaced plugs, then on one spark plug the plug wire refused to go all the way down. There was a gap of...

View more questions Search