Ask Experts Questions for FREE Help !
Ask
    sjmilks's Avatar
    sjmilks Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Jul 12, 2010, 12:25 PM
    I have 2 Goodman AEPF varialble speed airhand-2 techs, 2 diff dipswitch settings-HELP
    I recently had 2 Goodman systems installed, variable speed airhandlers AEPF 3017 with 2-ton 2 stage 16 seer condensing units. The same person did not install both units and both set the dipswitches differently. I've also read the installation instructions and they are not clear and state something different than what is stated on the airhandler motor label. What is the correct settings for the dipswithes?
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #2

    Jul 12, 2010, 02:12 PM

    The correct dip switch setting is determined by a service tech who uses a meter that measures air flow differential/pressure. It is not unusual for two different units to have two different settings to control air flow. NOTE: if you mess with the variable speed motor units you are asking for some VERY expensive repair work and the warranty does not cover tampering.

    In other words these type of units are NOT USER FRIENDLY. Sorry but that is the way they built them.
    sjmilks's Avatar
    sjmilks Posts: 2, Reputation: 1
    New Member
    		  
    #3

    Jul 13, 2010, 03:30 AM
    Comment on hvac1000's post
    Neither used any sort of meter to check CFM, both went by what they read on the unit or in the installation manual. I am a certified marine engineer with quite a bite of training and education in A/C and electrical. I also called Goodman but got suc
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #4

    Jul 14, 2010, 05:06 PM

    sjmilks : Neither used any sort of meter to check CFM, both went by what they read on the unit or in the installation manual. I am a certified marine engineer with quite a bite of training and education in A/C and electrical. I also called Goodman but got suc

    It is a shame they did not do there job correctly to start with. See this primer for adjustments. There is more to this than meets the eye.
    Attached Images
  1. File Type: pdf eginstallman.pdf (355.9 KB, 177 views)
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Goodman GMNT, noise and blower speed [ 4 Answers ]

I have a GMNT 120-5, the vent motor is extremely noisy during operations and can be heard in the entire house. Any possibility to repair or should I just replace the motor? After a recent service call the technicians switched the blower speed to a higher level which due to the high velocity now...

Goodman aepf air handler [ 0 Answers ]

I am currently having a problem with a goodman 16 seer air handler after the system meets temperature the blower motor keeps running. I have done several things and even called goodman tech support and got no help. I want to know if it has something to do with the purple wire that comes off the...

Goodman gks90904cxae‏ fan speed [ 1 Answers ]

I just got this hot air furnace installed Goodman gks90904cxae‏ Its got LP for gas The heat coming out is not as hot as my older one and I think the fan speed is way too high Anyone know how to set the fan speed on this particular model?

Variable speed settings [ 41 Answers ]

New Goodman 95% V/S furnace s not cycling as the brochure stated. States it runs 90% of the time to circulate air. My contractor says to fun the fan on the ON position to achieve but that will make it run 100% of the time. When in the auto setting it seems to cycle similar to the old heater, on...

Goodman furnace fan speed [ 1 Answers ]

How do I change the fan speed on a Goodman Dependable Ninety Two furnace.

View more questions Search