Ask Experts Questions for FREE Help !
Ask
    alfy871's Avatar
    alfy871 Posts: 1, Reputation: 1
    New Member
     
    #1

    May 26, 2009, 07:40 AM
    Adjusting pumptrol on well pump
    How do I adjust the cut in and cut out screws on the pumptrol. They are both out from the factry setting. I have the bladder type tank. I drained it completely an pumped it up to 25 PSI as recommended on the tank and filled the tank with water by pressing the contacts to 50 PSI the tank is now full, how do I adjust th cut in an cut out pressures. Must I drain the tank again?
    creahands's Avatar
    creahands Posts: 2,854, Reputation: 195
    Ultra Member
     
    #2

    May 26, 2009, 10:02 AM

    Turn power off to pump.

    Remove cover on pressure control.

    There are 2 screws. A long one and a short one.

    The long one will adjust both PSI on and off.
    The setting should be 30 psi on and 50 psi off.

    Turn power and run water. Watch contact for when it closes. This is your lower psi.

    Shut off water and watch contacts to open. This is higher psi. If 30/50, u are good.

    If adjustment is needed, turn off power and turn large screw 1 1/2 turns clockwise to increase pressure.

    Small screw adjust just lower setting.

    Bladder tank should be set 2 psi lower then low setting. If shut off is 30psi then tank should be set at 28 psi.

    To adjust psi in tank, will have to drain it.

    Inside cover usually has info on adjusting pressure control.

    Good luck

    Chuck
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
     
    #3

    May 26, 2009, 12:49 PM
    Quote Originally Posted by alfy871 View Post
    How do I adjust the cut in and cut out screws on the pumptrol. They are both out from the factry setting. I have the bladder type tank. I drained it completely an pumped it up to 25 PSI as recommended on the tank and filled the tank with water by pressing the contacts to 50 PSI the tank is now full, how do i adjust th cut in an cut out pressures. Must I drain the tank again?
    If you change the pressure setting on the control box you will have to shut the pump off, drain the system and recharge the bladder tank to the new pressure setting.
    Which nut adjusts water pump cut on or cut off?
    The larger nut in the pump pressure switch: Usually the larger nut in the pump pressure control switch adjusts the pump cut-on ("cut-in") AND pump cut-off pressures simultaneously. That means that whatever the gap is between the cut-on pressure and the cut-off pressure, that gap is maintained, but the entire operating range of the pump is raised or lowered. Turning the large nut clockwise RAISES BOTH the cut-on and cut-off pressures. So turning the large nut clockwise shifts the whole operating pressure range of the pump UP to HIGHER pressures.
    Conversely, turning the large nut counter-clockwise will lower the whole pump operating range. This is the simplest adjustment to make.
    The small nut in the pump pressure switch: this nut is used to narrow or widen the gap between the pump cut-on and pump cut-off pressures. Turning the small nut clockwise (tighter) will RAISE the CUT-OFF pressure, and vice versa, loosening or turning the nut counter-clockwise will lower the cut-off pressure. Watch out! If you loosen this nut too much you can set the cut-off pressure below the cut-on pressure and the pump will turn on and run forever (or until it burns up.)
    Which nut to turn in the pump pressure switch control, and which direction to turn it, are usually visible on a label inside the pressure switch cover. Above we show photos of a common Square D water pump pressure control switch and the label with pump control adjustment details
    Attached Images
     

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Adjusting pressure on Pumptrol Pressure Switch [ 9 Answers ]

Model #9013FSG2J21BP

Adjusting psi on Square D Pumptrol switch [ 1 Answers ]

My irrigation system requires the well pump psi to be set above 30 psi on the low end or else it drains the well. Once I cut the power and remove the cover to the Pumptrol switch, I turned down (clockwise) the center spring loaded screw down (the higher one upon which the cover was affixed). That...

Pumptrol water pump [ 1 Answers ]

I need to know how to prime a pumptrol water pump.

Adjusting my Jet Pump? [ 4 Answers ]

I recently replaced my pressure tank, which was a cast iron tank with a bladder tank. After doing so, I cannot seem to get the pressure in my system that I used to get. The pump has an adjustable screw on the housing next to the output, which I assume is a restriction valve. I do not know if I...


View more questions Search