 |
|
|
 |
New Member
|
|
Feb 18, 2009, 01:46 PM
|
|
Cutting notches a Corian countertop
I have a Corian counter top. I purchased a stainless steel slide-in range. Because the range is wider in the front, it will not slide all the way into the counter top opening. I need to cut notches in the counter top on either side of the opening about 1/2 inch wide by 2 inches deep. Can I do this using a circular saw with a carbide tip blade? Any tips on the process?
|
|
 |
Home Repair & Remodeling Expert
|
|
Feb 19, 2009, 11:45 AM
|
|
Put down duct tape around the area where you will be cutting. This will avoid scratches from the saw sole plate. You can also use a jig saw since you can't really make a notch with a circular saw.
|
|
 |
New Member
|
|
Feb 19, 2009, 02:47 PM
|
|
Thanks for the duct tape idea. What I meant to ask is, will the carbide tip circular saw blade adequately cut through Corian? I was planning to initially make the cuts with the circular saw, then cut the remaining material (that the circular saw blade cannot reach) with a jig saw. That way I will have a nice, clean cut where it is visible at the top & front after the range is installed. I have a hard time getting a straight, clean cut with a jig saw.
|
|
 |
Home Repair & Remodeling Expert
|
|
Feb 19, 2009, 02:51 PM
|
|
I hear you regarding the jig saw, they like to go where they want. Yes carbide is great but even a good steel blade will cut Corian, just will dull quicker. Jig saw blades have an undulation in th teeth, kind of a wavy set of teeth. You could try using a reciprocating saw with a spped control.
|
|
 |
New Member
|
|
Feb 19, 2009, 03:32 PM
|
|
I thought of the reciprocating saw too, but you wouldn't be able to use a fence to get a straight cut.
|
|
 |
Ultra Member
|
|
Feb 20, 2009, 01:24 AM
|
|
If you have a router it will make the cut you need using a straight bit.
Chuck
|
|
 |
New Member
|
|
Feb 21, 2009, 11:33 AM
|
|
That would be ideal, but my router is on the blink...
|
|
 |
Ultra Member
|
|
Feb 22, 2009, 01:14 AM
|
|
If using a jig saw buy a wide blade for it. Will hold the line better. Also hot glue apiece of 1X2 to corian as a guide. After u make the cut use a soap stone to ease the sharp cut edge. The duct tape can be put on after u glue the 1 by. For a cut as short as u have to make, the jig saw with guide should work fine.
Good luck
Chuck
|
|
 |
New Member
|
|
Feb 23, 2009, 05:23 PM
|
|
Thanks Chuck.
|
|
 |
Ultra Member
|
|
Feb 25, 2009, 08:32 AM
|
|
Hi gbgscw
Glad to be of help. Let us know how it turns out
Thanks
Chuck
|
|
 |
Junior Member
|
|
Mar 11, 2009, 08:27 AM
|
|
The corner of the notch should not be left square. This be a place for a crack to start. You should always raidus thi insid corners.
I am sure that you have done this job already. But for others you should drill a 1/2" hole where you want the corner to be then cut to the hole to make a proper installation.
Also, the saw marks should also be sanded out.
I hope this helps.
Ken
|
|
 |
New Member
|
|
Mar 11, 2009, 01:35 PM
|
|
Thanks Ken
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
Cutting a corian countertop
[ 4 Answers ]
I need to enlarge the opening for a new cooktop in my corian counter by 1/2 inch. I've been told that I can do this with my jigsaw and a wood cutting reverse blade after taping the area to be cut. Is this correct? If not, how would I do this? I would prefer to use my jigsaw rather then a router...
Corian countertop
[ 1 Answers ]
I need to find out how to repair my corain counter top it has a large crack. I have read about routing out 1/4" and how they have kits with glue and particles, BUT where can you get the kits?:confused: :confused: PLEASE HELP ME
Cutting through corian countertop
[ 1 Answers ]
What is the best way to cut through a corian countertop. We bought a new slide in range - but this one is a couple of inches wider than our old one. The countertop has to be cut to fit in the new range. Can anyone offer suggestions?
Corian countertop removal
[ 4 Answers ]
A friend has offered me his Corian countertops for my kitchen, if I come remove them from his kitchen. Do you need special equipment to cut Corian, or can you do it with a circular saw or reciprocal saw? Is there a certain blade type I should use?
View more questions
Search
|