Ask Experts Questions for FREE Help !
Ask
    SPARKY62's Avatar
    SPARKY62 Posts: 6, Reputation: 0
    New Member
    		  
    #1

    Mar 20, 2007, 11:57 AM
    Wiring hydro air and heat on the blower and boiler
    Hi ,
    I would like to know where do I make the connection on the blower unit for my hydro air - heat, when I use a aquastat to turn on the blower to operate during the heating cycle, is this the correct way of doing this. And also were do I hook up the wires on the boiler side
    I`am a bit lost when it comes to the hook up on the hydro side of it , please help thanks
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #2

    Mar 21, 2007, 04:02 AM
    Before you damage the unit I would seek professional help. There is actually quite a bit of wiring that has to be done and if not done correctly you will spend a lot of $$ on parts not covered under warranty.
    SPARKY62's Avatar
    SPARKY62 Posts: 6, Reputation: 0
    New Member
    		  
    #3

    Mar 21, 2007, 08:30 PM
    Quote Originally Posted by hvac1000
    Before you damage the unit I would seek professional help. There is actually quite a bit of wiring that has to be done and if not done correctly you will spend a lot of $$ on parts not covered under warrenty.
    Iam a retired electrician , just looking for some refresher know how!
    caibuadday's Avatar
    caibuadday Posts: 460, Reputation: 10
    Full Member
    		  
    #4

    Mar 22, 2007, 06:21 PM
    Quote Originally Posted by SPARKY62
    Hi ,
    I would like to know where do i make the connection on the blower unit for my hydro air - heat, when i use a aquastat to turn on the blower to operate during the heating cycle, is this the correct way of doing this. and also were do i hook up the wires on the boiler side
    I`am a bit lost when it comes to the hook up on the hydro side of it , please help thanks
    How about use the wall stat to control the boiler and the aquastat for the fan,use the one with at least 8F differential setting
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Hotwater heat (Boiler) [ 1 Answers ]

I have two zones heating my house,all rooms except one does not receive heat. All rooms on that one zone did not receive heat until I removed the air out of that zone my removing many buckets of water,one room at a time started to receive heat. I believe I removed all the air out of the line but no...

Air Cond blower motor wiring [ 2 Answers ]

I have a blower motor out of an Old air conditioner. It has 6 wires plus a green ground on the chasis. I assume this means it's a 3 speed motor? The motor is a KUSATSU Elec. CO LTD. Motor SN: 911483 "FC6T-61D1P". I Have searched all around and cannot find the information I need. I want to...

Help with Hydro air System please! [ 2 Answers ]

The problem goes like this. I have a Hydro air system that uses a fuel burning boiler. On the 1st floor -When the thermostat calls for heat, the boiler starts waits for the aquastat allowing the coil to heat up before turning the blower on. This is like a 10 to 30 second delay from the time the...

Boiler wiring [ 19 Answers ]

Ok, I will try to explain this the best I can with what I saw. I have an old repco boiler with 2 zones and I was wondering if the wiring was correct. The 2 zones are wired into a master control box then goes out to the pump on the boiler and the 2 thermos and another set of wires to another box(not...

View more questions Search