Ask Experts Questions for FREE Help !
Ask
    JohnCharles's Avatar
    JohnCharles Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Jan 21, 2012, 10:15 AM
    Furnace does not start
    What does no motor error code mean?
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
    		  
    #2

    Jan 21, 2012, 10:19 AM
    Are you saying you used to see a code light and it is not longer seen? I would start by confirming that there is power to the control board. Which furnace do you have?
    JohnCharles's Avatar
    JohnCharles Posts: 2, Reputation: 1
    New Member
    		  
    #3

    Jan 21, 2012, 10:28 AM
    Ballengeerb1 response to JohnCharles
    Thanks for response, there is a green light on, the red light is off. If I shut off power then restore power, both green and red light are on, furnace starts to cycle then about 15 seconds in red light goes out, motor shuts down, only green light remains on. The error code (one green constant light) means "no motor". It is a Kelvinator furnace installed last summer
    SeattlePioneer's Avatar
    SeattlePioneer Posts: 97, Reputation: 9
    Junior Member
    		  
    #4

    Jan 21, 2012, 12:09 PM
    Is the motor you refer to the inducer motor that circulates combustion gases through the furnace or the blower motor that circulates heated air through the house?
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
    		  
    #5

    Jan 21, 2012, 12:11 PM
    "installed last summer" so its still on warranty, right?
    T-Top's Avatar
    T-Top Posts: 1,871, Reputation: 100
    Ultra Member
    		  
    #6

    Jan 21, 2012, 05:31 PM
    Make sure you have the gas on going to the system.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Bryant furnace showing code 12-blower on after power up. Furnace won't start. Why? [ 0 Answers ]

Blower motor on all the time. No heat from furnace. Why?

Gas furnace blower motor won't start/slow to start [ 0 Answers ]

I have a airtemp probably 70's model we had to replace the blower motor about two years ago. Now when the fan is supposed to start it either won't start or is very slow to start. When this happens you can manually move the squirrel cage and it runs great through the complete cycle. We just replaced...

Furnace start up [ 3 Answers ]

I have a 7 year old Amana Furnace (80 SV) Mod# GUIDO70CA30 S/N: 991120784 The furnace will try to start several times and then shut down. The fuses and switches are all OK. The LED on the control panel does not indicate any trouble codes except a flashing 1 indicating a several start attempts...

Furnace ignites but blower won't start till furnace shuts down. [ 7 Answers ]

(Nordyne/Miller G3RA)-I have a furnace HSI(glow plug) that will ignite and burn until it gets too hot and shuts down. As soon as the furnace shuts down the blower starts to circulate air. The blower circulating air cools the furnace and it reignites.Shortly after the furnace ignites the blower...

Gas furnace has an intermittent pilot, pilot lights, furnace tries to start [ 3 Answers ]

Have a 25 plus year old furnace pilot will start when signal sent furnace tries to start makes noise as it tries over and over but will not start. Thanks

View more questions Search