Ask Experts Questions for FREE Help !
Ask
    rudyriehl's Avatar
    rudyriehl Posts: 1, Reputation: 1
    New Member
    		  
    #1

    Apr 17, 2011, 04:03 PM
    I have a Briggs & Stratton 18.5 HP that will not turn over.
    Used two different experts advice on the valve settings. Still acts like too much compression. Only way to get engine to spin is adjust valves to 0 clearance. Still won't start.
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
    		  
    #2

    Apr 17, 2011, 07:00 PM

    OK not sure what the other 2 told you so let me start at the beginning. Engine model would help.
    DG's Avatar
    DG Posts: 1,375, Reputation: 109
    Ultra Member
    		  
    #3

    Apr 17, 2011, 07:17 PM

    Bring to top dead center , then 1/4 inch past.
    Set valves between .004-.006
    Luck
    DG's Avatar
    DG Posts: 1,375, Reputation: 109
    Ultra Member
    		  
    #4

    Apr 17, 2011, 07:23 PM

    Not all just the intek.
    When you see 18.5 or most that have .5 in them there inteks.
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
    		  
    #5

    Apr 17, 2011, 07:25 PM

    Good to know, I have several and never noticed. Glad you are handling many of the engine questions. We have had several good guys come and go in the past. I'm the home repair guy and have been filling in when I knew the answers.
    DG's Avatar
    DG Posts: 1,375, Reputation: 109
    Ultra Member
    		  
    #6

    Apr 17, 2011, 07:29 PM

    You do a good job / and good answers .
    I don't get on here a lot this time of year,busy at my shop.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Toro Zero turn w/ 16 hp Briggs and Stratton [ 9 Answers ]

I have a Toro Zero turn 4200 with a 16 hp Briggs and Stratton motor. I have had the mower 4 seasons. When I try to start it the motor gets to the compression stroke and will not go any further. Sometimes if I turn it back and try again it will go past, pick up some momentum and fire up. I am not...

Briggs&stratton 20 hp motor will turn but will not start [ 1 Answers ]

20.5 briggs&stratton elect start,motor will turn fine but no spark, even checked to see if it had spark with plug, no fire

16 HP Briggs & Stratton will not turn over [ 1 Answers ]

I have a 16 HP Briggs & Stratton engine on a craftsman rider that will not turn over (crank.). I know the battery is good because I just replaced it and it sparked real good when the wrench hit both terminals accidentally. The model number is 310707-0136-E1 on the engine. It won't even click...

21 horse briggs & stratton will not turn over [ 2 Answers ]

I have a huskee 21 hp briggs and stratton that ran fine the day before and then I changed oil in it and tried to crank it and nothing happened. I bought a new interstate battery and new post connections and still nothing. I turn the key and get no sound what-so-ever. You would think the solinoid...

Briggs and Stratton 12.5hp engine won't turn [ 4 Answers ]

I have an older MTD with BS 12.5hp mower I inherited. I had to change starter when I got it and it ran fine. Last week I died on me twice (seemed to not get fuel and died). It started back up after 5 minutes without anything on my part. Today I go out and it turns over a little, then bogs down....

View more questions Search