Ask Experts Questions for FREE Help !
Ask
    Britton77's Avatar
    Britton77 Posts: 1, Reputation: 1
    New Member
    		  
    #1

    Feb 23, 2011, 03:51 PM
    a/c problem
    a/c blower fan turns on in "on" position. As soon as t stat is set to "cool"(blower in "on"or"auto position) the fan turns off and outside condenser unit does not turn on . The heat works normal. Main electrical power from breaker panel is fine. The outside condenser unit will run if the relay on the unit is manually ingaged. Any help or advice would be greatly appreciated...
    Theaircoguy's Avatar
    Theaircoguy Posts: 36, Reputation: 0
    Junior Member
    		  
    #2

    Feb 23, 2011, 06:36 PM
    It sounds like your circuit board needs to be replaced. Turn off the power to furnace. Remove the circuit board from furnace without disconnecting any wires. They sometimes show burn marks on the back of the circuit board when they go bad. (Not always) the circuit board is on the lower half of the furnace. Some are enclosed in plastic of either a beige or black plastic. You'll see a lot of wires going to it.
    Hope this helps.
    T-Top's Avatar
    T-Top Posts: 1,871, Reputation: 100
    Ultra Member
    		  
    #3

    Feb 25, 2011, 08:54 PM
    If you changed out your thermostat be sure to ad the jumper wire from RH to RC on the thermostat sub-base.
    Theaircoguy's Avatar
    Theaircoguy Posts: 36, Reputation: 0
    Junior Member
    		  
    #4

    Feb 25, 2011, 09:21 PM
    Comment on Theaircoguy's post
    Make sure that the thermostat is wired correctly as T-Top mentioned RH and RC need a jumper. The yellow wire needs to be connected to the Y terminal and at the furnace their should be two wires coming from outdoor unit. These don't matter what color they are. Typically they are red and white. One should go to Y terminal at furnace and the other to common or C terminal.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Central heating problem or water meter problem? [ 3 Answers ]

We live in an apartment building and the individual water usage is measured by private water meters (mechanical). When the apartment was built, 2 years ago, some of the meters had been fitted the wrong way (in reverse). Yesterday a plumber attended to rectify 3 meters. My 2 neighbours meters were...

Dachshund Back problem - urinating problem [ 6 Answers ]

My dachshund is now on box-rest after his back problems caused paralysis in his back legs. Is there any method to help him urinate or defecate?Basically after losing the use of his back legs, he has lost the ability to urinate or defecate by himself.

My 2006 Taurus has a problem hesitating to start sometimes, what could be the problem [ 1 Answers ]

Sometimes when starting my 2006 Ford Taurus, it hesitate to start, sometimes it does this and sometimes not, what could the problem? I'm thinking the starter. I replaced the battery, thinking it could be the battery, but the problem still exist. Help!

Playboy girlfirend problem.. Real problem [ 14 Answers ]

I have this new girlfriend.. that I really, really like (more than any other). She seems really nice... she was wearing everything of the "playboy" (earrings, bag, shirt, etc, etc) brand name / merchandise. I thought it was cute and a one time thing. Until I saw her bedroom.. It was 100%...

1995 Altima Idleing problem Knock & O2 sensor, EGR Flow Problem [ 1 Answers ]

I have 1995 Nissan Altima with 67,000 miles. When the car is idleing when I start it or when it is at a red light the rpm's go from 6000 to 9000. It sounds like I am reving the engine. The engine sounds fine when I am driving the car ( rpm's are consitent). I went to AutoZone the read out errors...

View more questions Search