Ask Experts Questions for FREE Help !
Ask
    peleroja's Avatar
    peleroja Posts: 3, Reputation: 1
    New Member
     
    #1

    Dec 30, 2010, 09:25 AM
    Cutting-seaming-corian-counter?
    I am wanting to redo a tiny townhouse galley kitchen, and have located some possible corian secondhand in good condition. My question is the piece for the sink/dw area is 58.5" and my area is 60" length/regular width, with a 36" sinkbase on the right and regular dishwasher to the left. Seller suggested using a backsplash type piece to cover the left end of the counter by the dishwasher outer panel area, but I am not sure this would work and look right. Suggestions or advice please - or should I even consider this?
    joypulv's Avatar
    joypulv Posts: 21,591, Reputation: 2941
    current pert
     
    #2

    Dec 30, 2010, 01:07 PM
    Do you mean a 1.5" piece of Corian glued edge to edge to the 58.5"? Sure, Corian is glued seamlessly all the time and it's one advantage over other materials.
    Are you OK with a 36" sink and a 24" dishwasher in a 60" space? I'd want a couple of inches between the dishwasher and whatever it is next to, insulated if a fridge, a brace if the wall or a stove. Someday you may need to stand on the counter.

    I'd have a 25" sink in a 27" cabinet, a 24" dishwasher, and a 9" cabinet on the end.
    peleroja's Avatar
    peleroja Posts: 3, Reputation: 1
    New Member
     
    #3

    Dec 30, 2010, 02:33 PM
    This is a townhouse galley style kitchen - the only thing on that wall is the dishwasher and the sink. There is a dishwasher cabinet area between the dw and the sink. Counter area on that side is above the dw. Stove/microwave, fridge are all on the opposite wall. LOL if I could redo the kitchen completely I would, but I can't because of the layout. Whoever built this didn't allow for any real future remodeling options because it is so tiny. Current countertop is tile and I hate it!
    creahands's Avatar
    creahands Posts: 2,854, Reputation: 195
    Ultra Member
     
    #4

    Dec 31, 2010, 09:50 AM

    Have u measured the layout of top and compared it to your cabinet layout?

    Is it possible to center the top on cabinets between the end walls? If so, use tile for back splash and side returns. At base of tile where meets top install ceramic decorative strip.

    The only place u will see short fall will be at front edge. This can be filled and painted color of top.

    Chuck
    peleroja's Avatar
    peleroja Posts: 3, Reputation: 1
    New Member
     
    #5

    Dec 31, 2010, 10:49 AM
    Again, there is no cabinet there other than the sinkbase and the dw panels. It is like a sinkbase bar area for lack of a better description. Thanks for the suggestions.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Cutting, seaming corian countertop [ 1 Answers ]

I have a free corian countertop, which is exactly the correct length for my kitchen countertop over my cabinets. However, the integrated sink is in the wrong place. I want to cut off one end and then take that piece and add it to the other end. I have the corian adhesive, which I bought over the...

Cutting Corian Counter Tops [ 4 Answers ]

I am installing a new burner unit in our Corian counter top. The existing cut out is 1/8th of inch too small so I need to shave 1/8th off one side of the cut out. What is the best method to do this? I have read that a regular skill saw will do.

Cutting corian counter top [ 6 Answers ]

What tools and what method can I use to enlarge a corian counter top cut out for a cooktop. I need to enlage the cutout by about 5/16 in in one dimension and 3/16 inch the other. The couter top is about 1 inch thick.

Corian Counter Tops [ 2 Answers ]

How do I polish corian counter?

Corian Counter [ 2 Answers ]

What tool would you use to cut Corian? I have a piece from an old kitchen counter that I want to cut into a 20"x20" cutting board. It is about 3/4" thick and the longest cut I have to make is about 24". Thanks


View more questions Search