Check out some similar questions!

grampy1953 · Jun 5, 2010, 04:21 PM

Is there a kit to change a "three handle" bathtub fixture (cold, shower, hot) to a single control fixture? If so where would I find such a kit and what is the kit called. Your help will be greatly appreciated..

cdad · Jun 5, 2010, 04:32 PM

There is no "kit" per say that Im aware of. The problem is that in a single confiruration the pipes will be a lot closer together. Also your going to need to seal the wall somehow if your not rebuilding. A combination of elbows and short nipples will get you in line pretty quickly. If your using existing copper lines then you will have to shorten the main lines a little to make room for the elbows and straights.

KISS · Jun 5, 2010, 05:58 PM

Califdad:

You didn't do your internet research properly.

It's called a re-model cover plate. Here is a link to a number of them: Replacing 3 hole faucet unit with a shower valve - TOH Discussions

cdad · Jun 5, 2010, 06:43 PM

Was thinking of the other kind where it comes straight out of the wall. The plates would have to be pretty wide to cover.

Guess that's what's called a brain fart ;)

KISS · Jun 5, 2010, 06:55 PM

They are. Here is the insruction manual: http://www.moen.com/shared/pdf/instr...ts/ins1911.pdf

They aren't cheap either.

cdad · Jun 5, 2010, 07:09 PM

The pictures on the other page looked a lot smaller. Lol

KISS · Jun 5, 2010, 07:14 PM

Beauty, in this case size, is in the eye of the beholder.:D

speedball1 · Jun 6, 2010, 05:21 AM

Originally Posted by grampy1953

Is there a kit to change a "three handle" bathtub fixture (cold, shower, hot) to a single control fixture? If so where would I find such a kit and what is the kit called. Your help will be greatly appreciated..

Yes 5there is! Moeen makes a remodel plate, (see image) to convert your old 5three knob valve to a single handled one. These chrome plates cover the three holes and are a attractive addition to any bathroom. If you need assistance in mounting your new valve we'll be glad to help. Regards, Tom

Milo Dolezal · Jun 6, 2010, 09:45 AM

Tom nailed it. Besides Moen there are few other manufacturers who make these plates. It will require some skill to switch from 3-handle faucet to single handle but you can certainly do it. Let us know how you did. Milo

KISS · Jun 6, 2010, 09:59 AM

Gee, what about my post on the re-model plate. You know sometimes I get left in the dark. It's even the Moen, with the model # and INSTRUCTIONS. Go figure.

Milo Dolezal · Jun 6, 2010, 10:00 AM

Kiss: Lol!

grampy1953 · Jun 8, 2010, 03:15 AM

Originally Posted by KeepItSimpleStupid

califdad:
You didn't do your internet research properly.

It's called a re-model cover plate. Here is a link to a number of them: Replacing 3 hole faucet unit with a shower valve - TOH Discussions

Thank You for starting me in the right direction. You are right I did not do my research properly. I am not the kind of guy to make excuses, so I must say the reason I didn't research the internet properly is because I am as much of a plumber as I am a spaceship pilot. I had no clue about a cover plate or even what to call it. Just call me a little slow, but I always thought not knowing is OK as long as you ask and learn. Stupid is when you do not know and will not ask and learn. I do appreciate your feedback. Maybe I can be of help to you on another subject.

Originally Posted by speedball1

Yes 5there is! Moeen makes a remodel plate,. (see image) to convert your old 5three knob valve to a single handled one. These chrome plates cover the three holes and are a attractive addition to any bathroom. If you need assistance in mounting your new valve we'll be glad to help. Regards, Tom

Tom, Thank You. I have worked on a few simple plumbing task, but this change in totally new to me. In other words I am far from being a Plumber. I had no idea about the cover plate. I may have to take you up on assisting me in mounting the new valve. At this point I have no clue what I am getting into until I get the old valve out and see what I will need to change over in regards to the pipe configuration. A tip for you will certainly be in order for help. Your response was greatly appreciated.

OOPS! I answered before I got down this far...

speedball1 · Jun 8, 2010, 06:28 AM

Gee, what about my post on the re-model plate. You know sometimes I get left in the dark. It's even the Moen, with the model # and INSTRUCTIONS. Go figure.

NOTICE: I give KISS full credit for mentioning Moen first. I didn't mean to hijack your post. My apologies!

Grampy, Here's another conversion remodel plate,(see image). There will be instructions with the new valve, Converting to a single handle is fairly simple. Your new valve will come with a round plastic cover you will use to cut a hole in the tile using the diverter hole as a center.
If there is no backing to secure the new valve I have had luck placing a piece of fur strip in front of the valve and tightening the face plate bolts against it.
If you have more questions we're as close as a click. Good luck, Tom