Ask Experts Questions for FREE Help !
Ask
    peteocpa's Avatar
    peteocpa Posts: 2, Reputation: 1
    New Member
    		  
    #1

    May 31, 2009, 07:33 PM
    Wiring Honeywell RTH7500 from a T8001r
    Have a multi-stage heat pump and this thermostat is one of the 3 located upstairs (there is one downstairs).

    Wiring on T8001r was
    Green = G
    Blue = C
    Yellow = Y
    Red = R
    White = W1

    There were no other wires hooked up and no jumpers.

    Installing the RTH7500 and I'm good up to the White wire. There is a note in the manual that states "If your old thermostat had Y1, W1 and W2 wires, stop now and contact a qualified contractor for help". Not sue if the key word is AND meaning that if all 3 were present to call a contractor. I'm thinking all I have to do is hook this White (W1) to Aux and run a jumper from E to Aux.

    Does that sound right?? Sure don't want to blow the system up or burn down my house. Figured it would be easy to just switch out units since they were both Honeywell.
    peteocpa's Avatar
    peteocpa Posts: 2, Reputation: 1
    New Member
    		  
    #2

    Jun 2, 2009, 12:55 PM

    Wow. I was sure hoping to get at least one reply to this. I guess I'm giong to have to just try it my way or call an HVAC contractor out.
    Joshdta's Avatar
    Joshdta Posts: 2,549, Reputation: 45
    Ultra Member
    		  
    #3

    Jun 2, 2009, 12:57 PM

    OK let me see and I can help you
    Joshdta's Avatar
    Joshdta Posts: 2,549, Reputation: 45
    Ultra Member
    		  
    #4

    Jun 2, 2009, 12:58 PM
    White to aux should be fine. I don't think you will have a need to put in the jumper to e the way this is setup.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Wiring Honeywell RTH7500 [ 1 Answers ]

I am replacing a White-Rodgers nonprogammable thermostat with a Honeywell RTH7500 programmable thermostat. This is the wiring config on the old thermostat. By the way I have a heat pump with emergency heat. B = Blue wire Y = Yellow wire G = Green wire R = Red wire W = White wire C = Brown...

Wiring for Honeywell RTH7500 thermostat [ 6 Answers ]

Hello, I am trying to install a new Honeywell RTH7500 thermostat to replace my Robertshaw 9200 thermostat. The Robertshaw 9200 had the following connections: One yellow wire that was connected to W and Y (the wire is long and was threaded underneath the screws in the W and Y connections);...

Honeywell rth7500. Can't figure out wires [ 1 Answers ]

I did a stupid. I took off the old non-progamable stat and didn't mark my wires. Here are the wires that I have. Red, yellow, blue, green, white and Orange. I'm not sure where they go. I have a Bryant furnace, heat pump and Air cond. This is a new house less than 6months old. Any...

Wiring a honeywell RTH7500 Programmable thermostat [ 1 Answers ]

I am replacing my old thermostat a Trane BAYSTAT240A with a honeywell RTH7500 series one. There were eight wires on my old W- B- X2-Y-G-O-R-and a T. There is no spot to hook up the T wire although I got the unit to work. Right now the biggest problem is I can't read the display good because the...

Replacing Honeywell T8411R with Honeywell RTH7500 - wiring problems [ 1 Answers ]

I need help getting my new, programmable thermostat to work. I currently have a dual-stage Heat Pump and A/C unit that works fine. The current thermostat is the Honeywell T8411R. I don't know the number for the subbase, but it's the one that came with the thermostat. The current (operational)...

View more questions Search