Ask Experts Questions for FREE Help !
Ask
    Valaury3169's Avatar
    Valaury3169 Posts: 2, Reputation: 1
    New Member
     
    #1

    Jan 30, 2009, 09:06 AM
    Installing water heater pan
    I am remodeling a house, and am about ready to install the hot water heater. The water heater will reside in an alcove in my laundry room (no room under the house). Per code, I have to install a pan under it. The alcove is wide enough to have a refrigerator and the water heater side by side... at least that is my hope. The pan that I purchased (and used to determine that the two will fit side by side) is slightly too small for the water heater to fit flat in without catching on the drain fitting (although the pan is a larger diameter than the water heater).

    My question is, would it be OK to elevate the water heater in the pan with masonry blocks similar to the way a HVAC air handler is elevated in its pan in an attic? This would allow me to clear the fitting, and not have to buy a larger pan, and probably cause problems with fitting the refrigerator and water heater side by side.

    Thanks.
    Milo Dolezal's Avatar
    Milo Dolezal Posts: 7,192, Reputation: 523
    Plumbing Expert
     
    #2

    Jan 30, 2009, 08:29 PM

    I don't think I fully understand: the fitting protrudes inside about 1/8". If it is still in your way than you bought small pan. Get larger. They make them in 2" increaments, meaning, you will add 1" on each side. I would not put the heater on bricks.

    Is your w/h elevated above the floor ? If positive, how much ?
    Valaury3169's Avatar
    Valaury3169 Posts: 2, Reputation: 1
    New Member
     
    #3

    Feb 2, 2009, 06:44 AM

    Why would you not recommend setting the w/h on bricks inside the pan? I am fine with that answer, I am just curious. Seems to me that if you do get a leak, then the w/h will be sitting in a pool of water until the leak is discovered and fixed.

    My problem is that in order to put the refrigerator and pan side by side in the alcove, I do not have room for a larger pan. The fitting actually protrudes inside the pan at least 3/4" if not more...it is a threaded fitting.

    The plan is to set the pan directly on the floor in the laundry room, with the w/h in the pan, although if I catch your hint, maybe I am supposed to elevate it on a platform? I can do that, although it won't solve my horizontal space limitations. If I can set the w/h on some concrete blocks (like maybe the 1-1/2" pavers) then the fitting will protrude under the w/h.
    iamgrowler's Avatar
    iamgrowler Posts: 1,421, Reputation: 110
    Ultra Member
     
    #4

    Feb 2, 2009, 07:26 AM
    Quote Originally Posted by Valaury3169 View Post
    Why would you not recommend setting the w/h on bricks inside the pan? I am fine with that answer, I am just curious. Seems to me that if you do get a leak, then the w/h will be sitting in a pool of water until the leak is discovered and fixed.
    The pan should have a drain opening on it.

    My problem is that in order to put the refrigerator and pan side by side in the alcove, I do not have room for a larger pan. The fitting actually protrudes inside the pan at least 3/4" if not more... it is a threaded fitting.
    Right.

    The fitting is intended to be used to drain the tank down, as well as to allow the tank to be flushed periodically.

    The plan is to set the pan directly on the floor in the laundry room, with the w/h in the pan, although if I catch your hint, maybe I am supposed to elevate it on a platform? I can do that, although it won't solve my horizontal space limitations. If I can set the w/h on some concrete blocks (like maybe the 1-1/2" pavers) then the fitting will protrude under the w/h.
    If you need to elevate the tank, then use a styrofoam pad to elevate it (unless it is gas fired, of course) -- Styrofoam pads in the correct diameter can be purchased where you bought the pan.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Need help deciding between a tank or tankless water heater [ 19 Answers ]

Which one saves me money; the tankless water heater or conventional tank water heater? :confused:

Reduced water pressure after installing new water heater [ 8 Answers ]

Quick history: 1. House is about 85 yrs old, two kitchens, two baths, and a laundry room sink near the water heater. Visible water main into the house is copper, however, after the water filter unit (with no filter element) is another foot of copper connected to galvanized piping. 2. Last...

Installing a hot water heater [ 11 Answers ]

I'm shopping for a hot water heater, and was just wondering if there's anything special I should be looking for--(efficiency,price,brandname), and if gas or electric is better, or more efficient. Also just wondering if there are any surprises in installing, or if it goes right in. It looks simple...

Installing water heater expansion tank [ 3 Answers ]

I'm on a water well system & a check value is installed between the well pressure tank and the Hot water heater. I think the check value is limiting the expansion of hot water & causing the T&P value on the hot water heater to open periododicly. Will installing a small hot...

Connecting a tankless water heater and separate hot water heater [ 6 Answers ]

What I have is this. An oil fired boiler that generates hot water for my house baseboard heating system. Contained within the boiler is a tankless heater that is heated by way of the firebox in the boiler. The tankless heater is used only for domestic hot water. It has a separate CW supply to the...


View more questions Search