 |
|
|
 |
New Member
|
|
Jul 20, 2006, 08:45 AM
|
|
Clunk and no pressure
When I turn on the hot water of my bathroom faucet it runs for about a second or 2 normally and then you hear a clunk in the pipes and the pressure drops way down and I only get a trickle. If I turn the handle slowly I can keep the pressure on the medium side for about 10 seconds then it clunks and drops to a trickle. I have switched the valves stems and get same problem. I am trying to sell my home and would like to try and get this fixed.
Any help is greatly appreciated.
Thanks.
|
|
 |
Expert
|
|
Jul 20, 2006, 12:00 PM
|
|
Do you have good pressure in the other pipes in the house ?
From the "design to sell" on TV, if you are trying to sell you want to put in new faucets anyway.
|
|
 |
New Member
|
|
Jul 20, 2006, 12:19 PM
|
|
The faucet is only a year old and is pretty nice so do not think the actual faucet is the problem. The rest of the house pipes have good pressure.
|
|
 |
New Member
|
|
Aug 4, 2006, 08:50 AM
|
|
Can anyone help me on this please?
|
|
 |
Eternal Plumber
|
|
Aug 4, 2006, 11:40 AM
|
|
 Originally Posted by Cheyfamily
Can anyone help me on this please?
I can try! One of two things are happening here. (1) you have a two handled faucet and the screw retaining the washer came loos and the washer's blocking the flow or (2) and this is my pick. A small pebble got in your water system and is lodged downstream of the angle stop. As the supplies are vertical the pebble drops down to the base of the supply until you make a draw. You will get pressure until this sucks the pebble up against the seat of the angle stop shutting off the flow. You already know which supply's affected. All that needs to be done is the hot water angle stop removed and the supply flushed out. Good luck and let me know.
Tom
|
|
 |
New Member
|
|
Aug 4, 2006, 11:47 AM
|
|
Thanks for sending some help Tom I will try this weekend to get this figured out. Question I have is how should I do this as I know it is only the hot water line in the bathroom? Should I open the faucet until the clunk and then close the angle stop and see if the possible pebble in the line between the angle stop and faucet or if it is not able to pass the angle stop?
|
|
 |
Eternal Plumber
|
|
Aug 4, 2006, 03:37 PM
|
|
 Originally Posted by Cheyfamily
Thanks for sending some help Tom I will try this weekend to get this figured out. Question I have is how should I do this as I know it is only the hot water line in the bathroom? Should I open the faucet until the clunk and then close the angle stop and see if the possible pebble in the line between the angle stop and faucet or if it is not able to pass the angle stop?
It sounds more like it's the angle stop seat that hangs it up. You can do the job yourself. Just shut the water off at the house shutoff and remove the angle stop. Place a pan over the open pipe and turn the water back on to flush out the supply. You should find it in the pan. Good luck, Tom
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
Pressure/bladder tank losing pressure?
[ 11 Answers ]
Well, I have asked some questions about my plumbing before. So I am calling on you guys once again. I have a 52 gallon pressure tank/bladder tank made by wellsaver. I turn the water on and have good pressure for a few minutes then it basically goes dead with no pressure. I recently posted questions...
Tank Pressure vs Pump Cut Out Pressure for Well
[ 1 Answers ]
I am trying to increase my water system pressure to the minimum required 40 PSI to feed my reverse osmosis drinking water filter. However, the 33 gallon pressure tank for my well pump system says it is pre-charged at 30 PSI and that the cut in pressure for my pump should be set equal to that 30...
Low pressure
[ 3 Answers ]
Ok, I have a rental house, got good pressure in the bath room on hot and cold, and in the kitchen got good hot water pressure. The cold in the kitchen is low. Any good suggestions at first places to look.
Low pressure on hot tap
[ 5 Answers ]
Hi can anyone help I have just installed a new mixer tap on my kitchen sink with a removable shower head the cold water is fine but the pressure on the hot is terrible is there any way to make it better?
Low water pressure in an area known for high pressure
[ 3 Answers ]
Greetings,
My wife and I are in the process of updating 1957 side by side split level. The previous owner (OK, my Mom as I bought the house I grew up in from her) said that when they moved in they had to install a pressure reducer into the line.
I have searched high and low but, I can't see...
View more questions
Search
|