Ask Experts Questions for FREE Help !
Ask
    cdefraia's Avatar
    cdefraia Posts: 14, Reputation: 1
    New Member
     
    #1

    May 29, 2008, 04:23 AM
    Pressure testing
    I am pressure testing the drain and vent stack in a new construction and want to know if there is any initial drop in pressure and is 5psi enough to test the system with.Also how long should it stay pressurized.
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
     
    #2

    May 29, 2008, 04:40 AM
    When we ready a drainage system for inspection we fill the stacks to overflowing the night before and let it set until the inspector passes it. 5 PSI works out to about a little over a 11 foot head. Isn't your stack higher then that? Multiply .434 by the distance between the base and the top of the stack to get the head pressure in PSI. Good luck, tom
    massplumber2008's Avatar
    massplumber2008 Posts: 12,832, Reputation: 1212
    Senior Plumbing Expert
     
    #3

    May 29, 2008, 05:01 AM
    Hey CDEFRIA:

    Like Tom said, plumbers almost always test the drainage/vent system using water to overflowing the roof vent.

    In my area, they also allow for an air test of 5 PSI to be held for 15 minutes minimum... BUT you must use a 5 PSI pressure guage that has increments of 1/10th PSI.

    That is my point, and only reason I popped in. Test pressures and testing times vary according to state.. so best is to call your local plumbing inspector and ask him exactly how he wants you to test the system.

    Otherwise, 5psi with the correct gauge should be fine... just note that the same test with the wrong gauge may not show the leak

    I still recommend testing with water myself!!!

    Good luck... MARK
    cdefraia's Avatar
    cdefraia Posts: 14, Reputation: 1
    New Member
     
    #4

    May 29, 2008, 04:05 PM
    Thank you speedball 1 and massplumber2008

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Pressure Testing an new underground gas line [ 16 Answers ]

Hi all, I am in the process of adding a new coated 1/2" natural gas line underground to a patio area. I wanted to pressure test it before I bury it and I cannot seem to find the leak. I have a gas pressure valve from Home Crapo that goes up to 15psi. I filled the pipes up with this on and...

Pressure testing a new gas pipe [ 1 Answers ]

Hi- We just plumbed a new gas pipe and are about to pressure test it. My son tested it at 25 psi for 2 hours but read another place it was to 15psi for 5 minutes- what are the correct standards Thanks, Lynne

Pressure testing [ 1 Answers ]

Who should I call for pressure testing for gas leakage in my house in Seattle, WA Thanks.

Pressure testing gas line [ 3 Answers ]

I am installing a new LP gas line into my basement. I have the line run and have a pressure tester connected to the line. I am getting conflicting info on the pressure and time I need to test to. I found an old thread (Aug 2005) on this forum that said 10 psi for 15 minutes. I also found a City...

Waste system pressure testing [ 2 Answers ]

What is the best way to air pressure test a new pvc waste/vent line? The plumbing inspector wants it air tested @ 5 psi for 15 minutes. This is the rough plumbing for a second floor addition, so I've glued all the pvc, but have not glued the connections to the main soil stack or to the main...


View more questions Search