Ask Experts Questions for FREE Help !
Ask
    silentbob152's Avatar
    silentbob152 Posts: 13, Reputation: 1
    New Member
     
    #1

    Nov 17, 2005, 10:28 AM
    Short Question About Flushing Water Heaters
    I've read in many posts here that it is important to flush your water heater regularly. All instructions have been to connect a hose to the boiler valve at the bottom of the tank and let it run until the water runs clear. My heater has a valve about halfway up the tank with a plastic hose running from it down to the ground. I put a bucket under this hose and opened the valve and some of the nastiest stuff I have ever seen came out. I let it run until the water ran clear. Is this essentially the same thing? Or should I still connect at the bottom of the tank to flush?

    Thanks
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
     
    #2

    Nov 17, 2005, 11:03 AM
    Hi Bob,

    " My heater has a valve about halfway up the tank with a plastic hose running from it down to the ground. I put a bucket under this hose and opened the valve and some of the nastiest stuff I have ever seen came out. I let it run until the water ran clear. Is this essentially the same thing?"

    Not even close,Bob. What you did was to open the T & P. Temperature and Pressure) valve. The minerals being heavier then water builds up in the bottom of the tank. To flush your heater you have to go where the crud lives. All you did was to blow out the trash the T & P valve collected over the years. Let me show you how to flush your heater. ATTACH A HOSE TO THE BOILER DRAIN AT THE BOTTOM OF THE TANK. With the pressure on, open the boiler drain and let it run until the water runs clear. You will see a spurt of red,(rust) and some white grains,(lime or calcium carbonate). The whole thing shouldn't take more then a few minutes. Don't forget to flush it out every month. Your heater will thank you for it. You might want to consider cleaning the screens on your areators if you have a high mineral buildup. If thev problem still persists after you have flushed, you will have to drain the heater, remove the boiler drain and go up in the bottom of the tank with a wood or plastic rod, (not metal) and try to break up the mineral and flush it out. Good luck, Tom
    silentbob152's Avatar
    silentbob152 Posts: 13, Reputation: 1
    New Member
     
    #3

    Nov 18, 2005, 07:43 AM
    Thanks Tom-

    While I'm not having any problems with the water in the house as it is, I'd sure like it to stay that way. I'll take your advice and go pick up a hose this afternoon.

    Thanks again for all your help thus far.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Tankless water heaters worth it? [ 4 Answers ]

Greetings all. I'm wondering what your expert opinions are of tankless "on-demand" water heaters (for the whole house). I found some supposedly new ones on EBay for about $750 (natural gas) and would do the installation myself. But I've never lived in a house that had one, and wanted to know if...

Noise when flushing toilet and when running water [ 1 Answers ]

I have humming noise (seems to be getting louder) when I flush the toilet and when I run water into the bath and into the kitchen sink. I read a reply to a similar problem about looking at the regulator.. What is a regulator? Many thanks!

Baseboard heaters [ 12 Answers ]

Hi all.. New to the forum.. Thanks in advance for any help.. I am trying to set up new baseboard heating in my basement.. My questions are to what size breakers to use and if I can put it all on one circuit.. I want to set up 3 rooms: Room 1 - 2 1000 watt heaters Room 2 & 3 - 1 1500 watt...

Installing new wall heaters [ 16 Answers ]

We currently have radiant heat. We must change over to electric wall heaters. My question spans the installation of the new heaters and if it is possible to use the existing wiring without rewiring and tearing into the sheetrock. I have outlined what we want to do. Any input as to if this is...

How to plan gas pipe job to hook-up tankless hot water heaters [ 7 Answers ]

Dear Ask Me Help Desk, I am installing two Paloma 200K BTU tankless hot water heaters in our L-Shaped 2900 square feet 1963-built rancher in Atlanta, GA. I am trying to decide if I should tackle the gas line part of the job. I have successfully done a number of small gas jobs which required...


View more questions Search