Ask Experts Questions for FREE Help !
Ask
    swein41's Avatar
    swein41 Posts: 1, Reputation: 1
    New Member
     
    #1

    Oct 29, 2007, 02:25 PM
    1999 taurus water pump
    How do you replace a 99 taurus water pump
    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #2

    Oct 29, 2007, 02:28 PM
    Here's how to do one on a Duratec, which I just did myself several weeks ago:

    Water Pump Removal: 2000 Taurus w/Duratec Engine

    1. Disconnect negative battery cable and, two minutes later, disconnect positive battery cable, to prevent accidental deployment of air bags.
    2. Remove serpentine belt.
    3. Place car on jack stands.
    4. Trick: Remove right-front wheel and plastic wheel-well liner (3 screws and 4 push pins), for access.
    5. Remove air dam and drain radiator.
    6. Disconnect radiator hoses from water pump.
    7. Remove antifreeze reservoir (degasser), for improved access.
    8. Remove tensioner pulley, for improved access.
    9. Remove water pump assembly, by loosening four 13 mm nuts securing the pump/housing to engine (3 from the top and 1 through wheel-well access) and three 10 mm bolts securing the pump/housing to the air conditioning compressor brace (through wheel-well access).
    10. Disconnect heater hose from water pump.
    11. Separate water pump from pump housing.
    12. Clean gasket and sealant material from pump housing.
    13. Coat new gasket, on both sides, with black RTV sealant, Permatex No. 2, or other suitable sealant.
    14. Install pump on pump housing and tighten the (7) M6x1.0, Grade 5, cap screws hand-tight. Then, tighten cap screws to 98 inch-pounds (lubricated), using a 5 mm hex bit socket. The Haynes Manual and AllData say to tighten the cap screws to 18 lb.-ft. which will strip the aluminum threads in the water pump.
    15. Install new pump/housing on engine, tightening the 3 bolts securing the air conditioning compressor brace to 18 lb.-ft. and the 4 nuts securing the pump/housing to the engine to 22 lb.-ft.
    16. Reattach radiator hoses, heater hose, button everything up, and refill with coolant.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Water Pump Removal: 2000 Taurus w/Duratec Engine [ 1 Answers ]

Water Pump Removal: 2000 Taurus w/Duratec Engine 1. Disconnect negative battery cable and, two minutes later, disconnect positive battery cable, to prevent accidental deployment of air bags. 2. Remove serpentine belt. 3. Place car on jack stands. 4. Trick: Remove right-front wheel and...

1999 Ford Taurus [ 3 Answers ]

I have a 1999 Ford Taurus V6 Vulcan, and I just installed a car stereo or car deck and when I flip the ignition backwards or key the car stereo does not turn on and I would like to know what's going on, its not any fuses cause I looked at them. Can anyone help me out here thanks. THanks

1999 Taurus won't start [ 1 Answers ]

My 1999 Ford Taurus has been a good car, but yesterday after getting home from somewhere, I went out to my car to run an errand. Even though I had driven it not 5 minutes prior, it won`t even turn over when I try to start it. I have checked every fuse relating to the starter, anyone know what`s...

1999 Ford Taurus [ 1 Answers ]

Vehicle intermittently down shifts (feels like Torque converter clutch disengageing) At highway speeds. Transmission was replaced issue still remains. FORD/Mecury dealers seem lost. Any Ideas No trouble codes. Thank you

1999 Taurus Transmission Problem [ 1 Answers ]

I'm looking for some help dealing with a 1999 Taurus LX Flex Fuel. In slow/bumper to bumper traffic, or at any slow cruise, such as looking for a parking spot, the transmission jerks between gears, as if it is looking for the gear it needs to be in. Seems to be shifting between 1st and 2nd gear....


View more questions Search