Ask Experts Questions for FREE Help !
Ask
    cj4215's Avatar
    cj4215 Posts: 4, Reputation: 1
    New Member
    		  
    #1

    Oct 7, 2007, 06:45 AM
    Maytag gas dryer heats intermittently
    I have a Maytag gas dryer that is two years old and not heating all the time. It runs intermittently. For instance, an average load can run for three cycles (50 minutes each) and still be damp. I can't buy a new one right now and would try to repair it myself before a costly service call. My son has thoroughly cleaned and vacuumed the vents. It heats briefly then apparently just blows cold air. The drum is turning but it won't dry my clothes. I think the days of the "lonely" Maytag man are gone. :) Help!!!
    esquire1's Avatar
    esquire1 Posts: 2,483, Reputation: 209
    Ultra Member
    		  
    #2

    Oct 7, 2007, 06:51 AM
    Did he remove the blower housing and clean it? This is usually clogs up first before the vent hose does. Check this and if problem continues,post back for further troubleshooting
    cj4215's Avatar
    cj4215 Posts: 4, Reputation: 1
    New Member
    		  
    #3

    Oct 7, 2007, 07:01 AM
    Yes, the blower was cleaned too. Thanks for asking and for your speedy response!

    Go Colts, that is a Colts logo, isn't it?
    esquire1's Avatar
    esquire1 Posts: 2,483, Reputation: 209
    Ultra Member
    		  
    #4

    Oct 7, 2007, 07:20 AM
    Yes it is "Colts" Get you unit back and going before they play at 4:05 today, OK
    cj4215's Avatar
    cj4215 Posts: 4, Reputation: 1
    New Member
    		  
    #5

    Oct 7, 2007, 07:37 AM
    This unit has been out of commission for two weeks! I'm about ready to lose my mind.

    Can you offer any additional troubleshooting advice?

    I'll accept any advice from a Colts fan!
    esquire1's Avatar
    esquire1 Posts: 2,483, Reputation: 209
    Ultra Member
    		  
    #6

    Oct 7, 2007, 08:19 AM
    Test the hi-temp thermostat. It could be bad and shutting burner down when the temp reaches that temp the will start back up at a lower temp. Pull one lead off it and check for continuity. Example, the lower temp stat may be marked 135 and the hi stat may be marked 165.
    cj4215's Avatar
    cj4215 Posts: 4, Reputation: 1
    New Member
    		  
    #7

    Oct 7, 2007, 06:41 PM
    LOL Doug, you think I have any idea what you are talking about?? I guess I better just breakdown and call the expert in! Thanks for your help I do appreciate it. I'll let you know what the experts say.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Maytag gas dryer [ 7 Answers ]

Dryer doesn't start up. Pushing the start button makes the normal "start" sound, but does actually start dryer. My wife did this the first time it stopped working. She stated that she could smell an "electrical smell". Where do I start?

Maytag gas dryer, replacing gas valve coils [ 5 Answers ]

Hi, I hope someone can help me. My Maytag gas dryer's igniter glows but then no flame appears. I believe it is the gas valve coils that are bad, so I purchased a replacement kit (3 coils). The instructions say to match the colors of the wires, but my replacement kit has red, black, white...

Whirlpool Dryer Heats Intermittently [ 1 Answers ]

Hi, I have a Whirlpool dryer Model# GGQ8858EQ1 that heats intermittently. I will turn on the dryer and the flame turns on but only heats up for 5 minutes then turns off. The dryer then runs the rest of it's cycle with no heat. I have tried replacing the fuse but that didn't solve the problem. I am...

Maytag Gas Dryer [ 1 Answers ]

What is the usual reason why a 1996 Maytag gas dryer doesn't heat properly. It seems to finally start getting warmer near the end of a long long cycle on Regualr heat, timed drying (or any of the other cycle choices)

Maytag gas dryer [ 2 Answers ]

My maytag dryer, model ldg482 runs but the heat does not come on. The igniter comes on but the gas doesn't ignite. Any suggestions?? The owners manual is totally useless and I'm reluctant to call in a service man to look at it since I have a complete tool shop and all tools to do anything.

View more questions Search