|
|
|
|
New Member
|
|
Feb 18, 2008, 11:11 AM
|
|
Residential Service Cable Type
Once again, a res. Question by a comm. Electrician. I have a new project relocating a meter service. The new meter will be about 25 feet from the 200A panelbox location instead of back to back. I'll wire in a 200A 2 pole breaker at the meter location as per 10 foot tap rule, and run new cable to panel. I need to go up new outside wall of addition across ceiling and down to existing panel. Can this be ran plenum up the wall and across ceiling, and down through existing pipe stubbed up from panel? I won't have a whole lot of room to get 2" pipe up wall, etc. if it's needed. If I can run it like cable, what is the cable designation that is approved for this? THANKS for any assistance!
|
|
|
Electrical & Lighting Expert
|
|
Feb 18, 2008, 12:11 PM
|
|
Use SER cable. That would be a typical installation.
4/0AL or 2/0cu depending on what they use in your area.
BTW- What "10' tap rule" are you referring to?
|
|
|
Senior Member
|
|
Feb 18, 2008, 04:22 PM
|
|
Why not install a meter socket with main breaker combination?
Question: Why is it that commercial electricians claim they can do residential electrical work, yet I haven't seen one that could rope a house? This is not to say "all" commercial electricians.
|
|
|
New Member
|
|
Feb 18, 2008, 05:55 PM
|
|
Thanks guys, excellent answers! The answer to your question, stan, is best described in previous question titled "10 foot rule- confused". And in answer to your question, Washington, your probably right, everyone has a specialty. And I'm a commercial control man actually, so I'm in real trouble no doubt! JK. - I'll call the power co. for a combo can, thanks!
|
|
|
Senior Member
|
|
Feb 18, 2008, 06:02 PM
|
|
Yeah, a combo is the way to go! Happy wiring! :) ;)
|
|
|
Electrical & Lighting Expert
|
|
Feb 18, 2008, 08:05 PM
|
|
Originally Posted by patholland
The answer to your question, stan, is best described in previous question titled "10 foot rule- confused".
Ahh.
Well, I won't comment on that thread other than to say much of it is misleading.
There is NO "10 foot tap rule". Even an unwritten one.
EVERY POCO has a different distance to the main disconnect. Some 10', some 2'-3'. Some immediately inside the structure. Some require the main disconnect outside. So any "10 foot rule" would strictly be a local thing.
This is why the NEC placed such ambiguous wording in this section. By this I mean the statement: "...nearest the point of entrance of the service conductors." They leave it up to the POCO to define what is "nearest".
Also, this has nothing to do with "taps". Taps are an entirely different thing. These are simply service entrance conductors.
|
|
|
New Member
|
|
Feb 19, 2008, 04:57 PM
|
|
You are completely correct, stan. I checked with the local inspector and he does require a disconnect at the meter outside since the panel is some distance away, but NEC is not specific on actual distance. I guess the lesson to all is to check with local authority on this issue before assuming anything. Thanks again for your input!
|
|
|
Senior Member
|
|
Feb 19, 2008, 06:31 PM
|
|
Originally Posted by patholland
You are completely correct, stan. I checked with the local inspector and he does require a disconnect at the meter outside since the panel is some distance away, but NEC is not specific on actual distance. I guess the lesson to all is to check with local authority on this issue before assuming anything. Thanks again for your input!
And the meter disconnect combination will work!:D
|
|
|
Electrical & Lighting Expert
|
|
Feb 19, 2008, 06:35 PM
|
|
Originally Posted by Washington1
and the meter disconnect combination will work!:D
I love 'em!
|
|
|
New Member
|
|
Feb 19, 2008, 07:13 PM
|
|
About that combo meter, my power company would only let me use their meter base. It was free, but not available with a disconnect. I got one from Lowe's for $135 and noticed they had a combo unit for $147. It was obviously easier to install than 2 separate enclosures and I would have paid the extra $12, but could not due to power co. regulations!
|
|
|
Electrical & Lighting Expert
|
|
Feb 19, 2008, 07:25 PM
|
|
I am surprised they did not have a list of acceptable substitutes. In fact, I am surprised they even still give out meter pans. Our POCO dropped that old routing years ago.
|
|
|
Senior Member
|
|
Feb 20, 2008, 08:20 PM
|
|
What a bunch of idiots! If they where smart, they could have saved their company some money!
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
Service entrance cable
[ 23 Answers ]
I am re-wiring an old house. It is a small 2 bedroom, 1 bath house. We put in a 200 amp service and need to run a service entrance cable about 20 -25 ft to the inside breaker panel. My question is how big of a gauge wire should we run for the service entance cable. #? 3 conductor with ground in...
Subpanel Cable type
[ 1 Answers ]
I need to install a 60amp sub panel. I will be running the feeder cable in Schedule 80 PVC. The run is 100 feet long, I want to use 2 gauge SE Quadruplex type RHW-2. Is this cable OK or should I be looking at something else. I want to be able to use it for 100 amps in the future.
Residential cleaning service
[ 3 Answers ]
My name is Mari. I recently started a cleaning company. I have already cleaned serveral homes but I am having a hard time as to what I am suppose to charge. I do not have much experience in this field but thought it would be a good flexible job while I am in school. I have tried to get advice...
View more questions
Search
|