Ask Experts Questions for FREE Help !
Ask
    pastor1189's Avatar
    pastor1189 Posts: 1,538, Reputation: 3
    Ultra Member
     
    #1

    Aug 5, 2012, 04:24 AM
    Changing Electrical Switches
    There is an existing bathroom switch that controls the overhead light.
    We want to add a switch outlet combination. So it controls the overhead light and makes the outlet always powered. I think now like all switch
    It is just the hot feed wire, interchanged. The white neutral wire just goes to the fixture. I am replacing a switch with a switch. Or must I pigtail
    The power feed
    Attached Images
      
    hkstroud's Avatar
    hkstroud Posts: 11,929, Reputation: 899
    Home Improvement & Construction Expert
     
    #2

    Aug 5, 2012, 05:13 AM
    Everything depends on how the present switch is wired. You must first determine whether the white wire you see in the switch box is a neutral or if it is part of a switch loop.

    If it is part of a switch loop the end of the white wire should be marked black in some manner. I say should be because, while this is a code requirement, is frequently not done.

    Examine the white wire and tell us what wires are in the switch box.

    The combination switch/outlet can be wired in several ways, depending on how you want to use it.

    Tell us what is in the switch box.
    pastor1189's Avatar
    pastor1189 Posts: 1,538, Reputation: 3
    Ultra Member
     
    #3

    Aug 5, 2012, 05:58 AM
    The white wire is uninterrupted. The feed wire is cut and runs through the switch
    On the two screw. That is about it. It looks like I would have to pigtail the white neutral wire
    To the silver screw and then join all the neutral wires together
    shuntripper's Avatar
    shuntripper Posts: 180, Reputation: 8
    Junior Member
     
    #4

    Aug 5, 2012, 04:03 PM
    Quote Originally Posted by pastor1189 View Post
    The white wire is uninterrupted. The feed wire is cut and runs through the switch
    on the two screw. That is about it. It looks like I would have to pigtail the white neutral wire
    to the silver screw and then join all the neutral wires together
    First, before you do anything more, Is this switch going to be within 6 feet of the sink or tub? Because if it is, you may have to make this into a 2 gang box so the receptacle is a GFCI, or forget about putting the receptacle there. I've never seen a stack switch GFCI

    (edit) but holy smokes look what I found! If sink/tub too close you have to use this.

    http://www.westsidewholesale.com/lev...15_a_7c1983556

    ( I don't do residential, didn't occur to me this thing might exist)




    By "uninterrupted" do you mean the neutral is not landed on the existing switch? It is not used? (logical) and is actually two ends wire nutted together?

    Do you have a voltmeter? Do this with the switch still hooked up as it always has been, circuit still on, label what you find.
    Check to see if you read 120V (or so) between the white and either one of the black wires on the switch with the switch in the Off position.
    This will tell you if the white wires are really a neutral or a switch leg. If you read voltage about 110-120V, then the white wires are neutrals and (switch off) the black wire where you can read voltage is the incoming hot wire.
    If you turn the switch On, both of the blacks will read voltage to neutral (or to ground) the one that does not stay hot when you put the switch in the Off position is the Switched Leg/Loop.

    To wire the combo switch/receptacle on a single strap (like your picture) you can take the black wire that stays hot all the time whether the switch is on or off
    And land it under the yellow/brass color screw. The Switch Leg (black wire, goes on and off when toggling the switch) goes under the Black screw
    The White wire pigtial coming from the wirenutted junction of the neutral wires goes on the white/silver screw.


    you will see two Yellow/brass screws on this switch, electrically they are the same unless the brass tab you can see between them(usually slotted ) is removed. This is to allow "split wiring" this combo either with another switch leg for switched receptacle from another switch or the switch leg from the switch on top so that switch can turn it on and off.
    pastor1189's Avatar
    pastor1189 Posts: 1,538, Reputation: 3
    Ultra Member
     
    #5

    Aug 6, 2012, 05:18 AM
    Very Good. It is not near a tub or sink. Great wiring description
    shuntripper's Avatar
    shuntripper Posts: 180, Reputation: 8
    Junior Member
     
    #6

    Aug 6, 2012, 06:55 PM
    I'm glad you found it helpful (hint hint) that last paragraph looked kind of confusing no matter how I wrote it.
    pastor1189's Avatar
    pastor1189 Posts: 1,538, Reputation: 3
    Ultra Member
     
    #7

    Aug 7, 2012, 04:24 AM
    Extremely pleased

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search


Check out some similar questions!

Electrical.. Two Way Switches [ 4 Answers ]

I Have A Two Way Switch At The Top Of My Stairs Leading To The Basement & A Two Way At The Bottom Of The Stairs In The Basement.. They Are Connected With A #8 Wire I Think.. Round Wire With A Blk,White & Red.. I Was Doing Renovations & I Pulled The Wires Of The Switch In The Basement & Now It Does...

Changing switches [ 4 Answers ]

Yes I know have 2 turn buttons where I can adjust my light brightness and fan speed I would like to put in a switch to turn light on and off.Then I can adjust the fan with a pull string on the fan. There are all sorts of wires inside the box on the wall where do I start. Thanks for any and all...

Electrical switches [ 17 Answers ]

:confused: hello, I need to replace an electrical blower fan switch on an old car. I can't find the same one as the car is old. The switch is a off, 1st speed, 2nd speed 3rd speed, high speed, sliding handle type switch. Its been going out for years and finally just won't work. I know the blower...

Electrical switches [ 2 Answers ]

Hi, why do my light switches snap when I turn them on?


View more questions Search