 |
|
|
 |
New Member
|
|
Oct 2, 2009, 04:29 PM
|
|
Difficulty removing tub spout
Hi everyone,
I am trying to remove a tub spout without much luck. I looked underneath and couldn't find a set screw. It is tight and does spin with a fair amount of force, but does not come off. It sounds like it is clicking when I am spinning it.
Any ideas before I call a plumber out?
Thanks,
Matt
|
|
 |
Junior Member
|
|
Oct 2, 2009, 04:32 PM
|
|
It sounds like you may have rotated it past the set screw.
|
|
 |
New Member
|
|
Oct 2, 2009, 04:38 PM
|
|
 Originally Posted by Widdershins
It sounds like you may have rotated it past the set screw.
Thanks for the reply. On the bottom of the spout on the back there is an opening like 1/8 of an inch big. I got down in the tub and looked and couldn't see a set screw. I figured this fixture just twisted off.
|
|
 |
Junior Member
|
|
Oct 2, 2009, 04:44 PM
|
|
If it just keeps spinning and doesn't unscrew out, then it is a slip on spout and there should be a set screw -- Another dead giveaway is the clicking sound you described in your first post.
Keep rotating it slowly until you see the set screw -- Try to avoid being aggressive with it as you rotate it, lest you further damage the copper stub-out.
|
|
 |
New Member
|
|
Oct 2, 2009, 04:58 PM
|
|
 Originally Posted by Widdershins
If it just keeps spinning and doesn't unscrew out, then it is a slip on spout and there should be a set screw -- Another dead giveaway is the clicking sound you described in your first post.
Keep rotating it slowly until you see the set screw -- Try to avoid being aggressive with it as you rotate it, lest you further damage the copper stub-out.
Will do, I figured the opening was so small it was a weephole or something. Thank you.
|
|
 |
Junior Member
|
|
Oct 2, 2009, 05:03 PM
|
|
 Originally Posted by mattb1
Will do, I figured the opening was so small it was a weephole or something. Thank you.
Would it be possible to upload a photo of the spout?
|
|
 |
Plumbing Expert
|
|
Oct 2, 2009, 05:27 PM
|
|
Also, and to addition to the advice above: sometimes, you can pull on the spout and it will slide out.
|
|
 |
New Member
|
|
Oct 2, 2009, 05:58 PM
|
|
 Originally Posted by Widdershins
Would it be possible to upload a photo of the spout?
OK:
|
|
 |
New Member
|
|
Oct 2, 2009, 05:59 PM
|
|
 Originally Posted by Milo Dolezal
Also, and to addition to the advice above: sometimes, you can pull on the spout and it will slide out.
Tried and wouldn't budge. Thanks though!
|
|
 |
Plumbing Expert
|
|
Oct 2, 2009, 06:00 PM
|
|
It looks like it unscrews . I don't see hole for set screw. Try to put channel locks around it and turn it CCW. See what it does...
|
|
 |
Eternal Plumber
|
|
Oct 3, 2009, 06:19 AM
|
|
Keep rotating it slowly until you see the set screw -- Try to avoid being aggressive with it as you rotate it, lest you further damage the copper stub-out.
Will do, I figured the opening was so small it was a weephole or something.
Diverter spouts don't have weep holes. You have a slip on spout. Widdershins nailed it when he said,
It sounds like you may have rotated it past the set screw.
(see mage). Twist it to reveal the Allen Head Set Screw and loosen it and pull the spout free. Good luck, Tom
|
|
 |
Junior Member
|
|
Oct 3, 2009, 06:43 AM
|
|
 Originally Posted by speedball1
Diverter spouts don't have weep holes. You have a slip on spout. Widdershins nailed it when he said, (see mage). Twist it to reveal the Allen Head Set Screw and loosen it and pull the spout free. Good luck, Tom
I don't know, Tom, now that I've seen a photo of it I'm thinking it might be the Moen Château spout with soap tray. If it is, then it will be an IPS connection.
|
|
 |
Ultra Member
|
|
Oct 3, 2009, 07:31 AM
|
|
 Originally Posted by Milo Dolezal
It looks like it unscrews . I don't see hole for set screw. Try to put channel locks around it and turn it CCW. See what it does...
I agree with Milo, if you don't see a small window and a set screw underneath, don't be afraid use a bigger channel lock turn it CCW turn the spout 180 degrees once again look if you see a cutout and see a set screw, remove the set screw and turn the spout CCW and CW, see if get loose some time it is just stuck on nipple, one other thing I have seen that set screw was missing and I assumed that it threaded type by turning the spout left and right it came loose.
If it is not the slip type spout to use a bigger 18” Chanel lock you would have luck to remove is,
And may I ask why would you remove the spout? Thanks.
John
|
|
 |
New Member
|
|
Oct 3, 2009, 07:40 AM
|
|
 Originally Posted by afaroo
I agree with Milo, if you don't see a small window and a set screw underneath, don't be afraid use a bigger channel lock turn it CCW turn the spout 180 degrees once again look if you see a cutout and see a set screw, remove the set screw and turn the spout CCW and CW, see if get loose some time it is just stuck on nipple, one other thing I have seen that set screw was missing and I assumed that it threaded type by turning the spout left and right it came loose.
If it is not the slip type spout to use a bigger 18” Chanel lock you would have luck to remove is,
And may I ask you would you remove the spout? Thanks.
John
Thanks for the information! I'll try again as it is really hard to see in that small hole.
It is hard to see in the photo but it is cracked in the front and the diverter doesn't work as well as it should as a result.
|
|
 |
Senior Plumbing Expert
|
|
Oct 3, 2009, 03:36 PM
|
|
Hi Tom...
Matt took a picture of the bottom of the spout in POST #8... ;)
Matt will need to remove this by spinning counterclockwise (as pointed out by Milo) and he may need to jiggle the spout up and down and pull all at the same time to remove it. Sounds to me like the soldered joint or the threaded joint has come disconnected and is just stuck on and being stubborn.
Matt, let us know...
MARK
.
|
|
 |
Eternal Plumber
|
|
Oct 3, 2009, 04:17 PM
|
|
Thanks Mark,
It didn't come up to where I could see the entire spout, I think you're right. It's a threaded spout that the adapter has cone unsoldered. If the spout's made of plastic I'd destroy the spout and see what's holding it from coming out. Cheers, Tom
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
Removing tub spout
[ 9 Answers ]
I just moved into an older house that doesn't have a shower and I'm trying to replace the tub spout to add one with a personal shower attachment. For some reason I can't get the old spout of. There are no screws on the outside of the spout. I've chipped away the putty and used wd 40 but I still...
Removing Tub Spout
[ 2 Answers ]
Hey Gooseproints, I am having the same problem removing the tub spout.
There is a cutoff at the bottom, but I cannot find any set screw. I see the plastic "X". I can turn the spout counter-clockwise, but it just turn without moving out. I would not turn clockwise, only counter-clockwise. I try...
Removing tub spout
[ 1 Answers ]
I have read all the posts I could find on changing tub spouts but I can't even get mine off. We have been having trouble with it for quite some time and today the shower diverter actually came out and the little white plastic piece fell out too. I can see how it works but I can not get it back...
Removing Tub Spout
[ 7 Answers ]
I know this has been discussed in length, but I don't want to bust something trying to do it the wrong way. I have tried to turn the spout counterclockwise and it won't budge. Any ideas?
http://i277.photobucket.com/albums/kk79/telluriccheese/P1050042-1.jpg
...
View more questions
Search
|