Ask Experts Questions for FREE Help !
Ask
    sonnystables's Avatar
    sonnystables Posts: 1, Reputation: 1
    New Member
    		  
    #1

    Dec 7, 2007, 07:40 AM
    Need wiring information on a heat pump to a oil furnace
    All,
    I have had 4 people come out to fix the wiring on our newly installed system, the installer included.

    Here is the situation
    Basically the when our system calls for heat the blower comes on as soon as the heat, no matter if it is heat pump or Oil and also shuts off at the same time. When using the emergency oil only the system doesn't heat up properly, so bacically the Limit Control then doesn't cool the system down.

    Our setup:
    White Rodgers Blue 90 Thermostat 1F95-1227
    White Rodgers external temp controler
    Goodman HP - GSH130301
    Bard Furnace - FH110D48C

    Any Ideas that I can pass on to a installer?

    Thanks
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #2

    Dec 7, 2007, 09:26 AM
    Yes buy a fossil fuel kit and wire it according to directions OR buy a honeywell 8000 series tstat the has the equivalent of a fossil fuel kit in the stat built in.

    This has been a huge problem for many service people and I do not understand how they can continue to sell this setup if they do not know how to make it work.

    I cannot find your thermostat listed? Did you post the incorrect part number.

    Here are a few to look at that will work but you have to READ to find it.

    http://www.white-rodgers.com/wrdhom/...6_pg0008_9.pdf

    OR

    http://www.white-rodgers.com/wrdhom/.../0037-6753.pdf
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

NO HEAT! Janitrol heat pump and AC system. Changing to Lux Thermostat. Wiring issue. [ 11 Answers ]

I have a Janitrol A/C and heat pump system. I replaced the thermostat with a Lux T9000LC The A/C works fine, but the heater does not. I have it wired as follows: G - Green Y - Yellow W - White RH - Pink B -

Heat pump wiring up to code [ 5 Answers ]

I had an eletrical surge (low voltage) burn out my 10 year old 3 ton Carrier compressor, a month ago. Electrican said it was caused by a power surge. Electric co states it was faulty in house wireing They told me that my 10 year old compressor was supposed to have a 35 amp rated circuit breaker...

Heat Pump? A/C? New Furnace [ 9 Answers ]

A/C died over the weekend. Repair guy checked the system and found "the compressor seemed to be drawing high AMPs". Replaced a blown fuse and then quoted me $4800 for a whole new system. Quoted Armana Distinctions 70,000 BTU 95% furnace, 2.5 ton 13 seer condenser, coil and pump. Figured that I...

Wiring Diagram for heat pump with gas furnace [ 1 Answers ]

75,000 BTU Concord furnace with 2 ton heat pump.. Chromatherm Thermostat and when the heat comes on both the heat pump and gas furnace are running... How do I correct the wiring malfunction so the heat pump initially comes on and the gas furnace comes on when the pump can't keep up or in the event...

Heat pump thermostat wiring [ 1 Answers ]

I have pored over the thermostat wiring messages on this forum, but I still have a question. I am installing a RiteTemp 8085C to replace a Janitrol thermostat for my Goodman heat pump. The old thermostat was wired as follows: Red to R Orange to O Yellow to Y Green to G Blue to C White...

View more questions Search