Ask Experts Questions for FREE Help !
Ask
    Mikef's Avatar
    Mikef Posts: 3, Reputation: 1
    New Member
     
    #1

    Oct 11, 2007, 06:41 PM
    Remove Drum, Matag Top Loader
    I have a Matag washer (Model LAT8506AAE) - two belts on the bottom.

    The washer won't spin out. It turns, but somewhat hard, even when in the spin cycle (brake off? ). It turns (by hand) when I take the belt off and start the spin cycle. There is no obvious grinding that might signal bad bearings.

    I changed the belts, but still won't turn.

    I have the agitator off, and there's a large "nut"? That is like an upside down coffee cup with 8 notches and a rubber center around the agitator shaft. I'm assuming that the notches are for some specialized tool. I can get a pipe wrench on it, but can't budge it.

    Does this turn clockwise or counter clockwise. Any other help on getting the drum out?

    Mike
    esquire1's Avatar
    esquire1 Posts: 2,483, Reputation: 209
    Ultra Member
     
    #2

    Oct 12, 2007, 02:27 PM
    It is a left-handed spanner nut that you need to remove. It does take a spanner nut wrench but may be able to remove with a pipe wrench or a screw driver set in the groove and tap on it with a hammer. Careful this way though so you don't damage the nut.
    GlenNeff's Avatar
    GlenNeff Posts: 1, Reputation: 1
    New Member
     
    #3

    Apr 29, 2008, 09:01 PM
    I have the same model washer and the same problem.

    Did you figure out what the problem is? Also, if I have to remove this spanner nut, I'm not clear what you mean, esquire1. If it's a "left-handed-spanner nut," does that mean you have to turn it opposite of "lefty-loosy" to remove it?

    I've found a rough photo of the nut in question: Model LAT8506AAE
    esquire1's Avatar
    esquire1 Posts: 2,483, Reputation: 209
    Ultra Member
     
    #4

    Apr 30, 2008, 08:22 AM
    Yes, oppisite of lefty loosey

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Replacement lint filter - Samsung Top loader [ 2 Answers ]

Hi. I have a Samsung Triflow SW65ASP2 Top loader which is nearly 5 years old. I have just noticed that the 2 lint filters are shreded from use and have no idea where (or even if I can) get replacements. I bought the Machine at Myer (and have never seen any there). I have a toddler and a baby so...

Kenmore elite top loader will not spin... [ 2 Answers ]

I have a Kenmore Elite (calypso) Model#110.21062000 that will not move from the rinse cycle into the spin cycle. It will give to different error codes occassionally: 1) "LD" - long drain, 2) "SL" - suds lock. In both cases the unit appears to be draining without any difficulties as observed by the...

Matag Washer, How do I remove Agitator? [ 3 Answers ]

I have a newer Matag Toploading washer (model starts with LAT8506) and the tub won't spin. I'm trying to work on it, but I can't get the agitator off. I've tried pulling up very hard (there is no bold down the center hold). I'm guessing that the clutch won't let go, or there's a transmission...

Poorly agitating Whirlpool top loader - no resistance [ 1 Answers ]

My Top loading whirlpool washer is agitating very weak. When it was new, the agitator had ~40 #' s of resistance and now I'm getting about 5# of resistance, resulting in the clothes not getting clean. Can someone tell me what this is or may be.


View more questions Search