Ask Experts Questions for FREE Help !
Ask
    scuba1955's Avatar
    scuba1955 Posts: 1, Reputation: 1
    New Member
     
    #1

    Sep 22, 2007, 08:25 AM
    Working with old cast iron plumbing
    What is the best way to remove lead pipe from old cast iron with out destroying the cast iron? Also the best way to then connect pvc to cast iron.
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
     
    #2

    Sep 22, 2007, 09:31 AM
    Quote Originally Posted by scuba1955
    What is the best way to remove lead pipe from old cast iron with out destroying the cast iron? Also the best way to then connect pvc to cast iron.
    Cut out the old lead pipe all the way back to the brass caulking ferrule. This should bring you up to the lead and oakum joint in the cast iron hub. You will now have to remove the brass ferrule and lead joint. To remove a poured lead and oakum joint take a 3/8" drill bit and drill a few holes down past the lead and into the oakum.. Push a screwdriver under the lead ring and lever it up. Once it's free you can began to peel the lead ring out. Now pick out the oakum and you can pull the joint apart.
    OK! Now you are left with a open hub. A Neoprene Gasket,)(see image) will then be inserted into the hub and the PVC into that. Let me show you how.
    Duel Tite connections go like this. You first insert the gasket into the hub of a cast iron fitting. Next you paint the inside of the gasket with Duel Tite Lubricant and file a bevel on the end of the PVC pipe so it will slip in and start to seat. Now paint the pipe and insert it into the gasket making sure that it goes in straight and not cocked. If there's a problem getting it started it's acceptable to take a knife and trim the first few ridges off the front of the gasket. Now simply place a Johson Bar, (And I'll bet you thought a Johnson Bar only lived in your trousers) on the end of the PVC and push it in until it seats. Good luck, Tom
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
     
    #3

    Sep 22, 2007, 03:38 PM
    What part of this did you not understand? OK! Now you are left with a open hub. A Neoprene Gasket,)(see image) will then be inserted into the hub and the PVC into that. Let me show you how.
    Duel Tite connections go like this. You first insert the gasket into the hub of a cast iron fitting. Next you paint the inside of the gasket with Duel Tite Lubricant and file a bevel on the end of the PVC pipe so it will slip in and start to seat. Now paint the pipe and insert it into the gasket making sure that it goes in straight and not cocked. If there's a problem getting it started it's acceptable to take a knife and trim the first few ridges off the front of the gasket. Now simply place a Johson Bar, (And I'll bet you thought a Johnson Bar only lived in your trousers) on the end of the PVC and push it in until it seats. Back to you. Tom

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Moving Cast Iron Toilet Plumbing [ 2 Answers ]

Hello all, I'm starting down the path to redo my one full bathroom in an older (1920s) house. In planning it out, I have determined that the drain from the toilet is cast iron. My plan includes moving the toilet, which I know means I have to move the drainage as well. Should I expect to run...

Cast Iron Lead sealed plumbing [ 1 Answers ]

I have an older home that has a vented stand cast iron plumbing (4-6" diameter), and the joints are sealed with lead. I need to rotate one tee joint (runnuig vertically). Do I have to heat the lead to a molten state to allow rotation? I have never worked with lead sealed pipe and while this...

Cast iron [ 2 Answers ]

Hi folks, What is the best way to repair a leaking tub drain that connects to cast iron main drain? Thank you, Jen

Rotating Cast Iron Plumbing [ 3 Answers ]

1956 vintage house with cast iron plumbing has the washer pump out line through a typical P trap into a threaded connection on a 2 inch by 1.5 inch CI tee in a vertical run (up to a vent to roof, down into the slab and sewer system). Unfortunately, the tee branch points out into the laundry room...


View more questions Search