Ask Experts Questions for FREE Help !
Ask
    roycemek's Avatar
    roycemek Posts: 44, Reputation: 2
    Junior Member
    		  
    #1

    Jun 1, 2007, 12:06 PM
    200 Sub-Panel Location
    Is it OK to mount a 200A sub-panel in a utility closet? What are the rules related to the location for sub-panels within a single family dwelling? The main is a 400A meter main located outside attached to the garage. This is for my home in Burbank, CA.

    Thank you,
    Royce M
    tkrussell's Avatar
    tkrussell Posts: 9,659, Reputation: 725
    Uber Member
    		  
    #2

    Jun 1, 2007, 12:28 PM
    The only locations restricted by national code is a panelboard cannot be located in a clothes closet or a bathroom.

    Best to check with local codes, as I know of one state that does not allow panelboards installed under stairs.
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
    		  
    #3

    Jun 1, 2007, 01:32 PM
    Tk, is current code also, 30" side to side, and 36" in front clearance?

    Haven't had to get close to the limits for a while? Thanks

    Poster, Like above, check local codes
    tkrussell's Avatar
    tkrussell Posts: 9,659, Reputation: 725
    Uber Member
    		  
    #4

    Jun 1, 2007, 01:36 PM
    Yes on the clearances. The 30 inch can begin on one side of the panel and go 30 in to the other side. Does not need to be centered.

    The 36" in front is still standard, this clearance gets larger as thew voltage rises, or gear is facing each other.
    roycemek's Avatar
    roycemek Posts: 44, Reputation: 2
    Junior Member
    		  
    #5

    Jun 1, 2007, 09:26 PM
    Thanks guys. I spoke with the electrical inspector for my area and he said basically what was mentioned above. No other special rules.

    Best regards,
    Royce M
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

200 amp panel feeding a 100 amp panel roughly 130' away [ 7 Answers ]

Hi all, We are building a apartment above the garage,my question is what size wire do I need to run from the 200 amp panel to the 100 amp panel roughly 130' away? I want to use aluminum wire as I think copper would be to costly. Thanks for your help in advance, Dude :eek:

? Adding a pool filter to a 200 amp panel [ 2 Answers ]

I have a 200 amp service and would like to add a pool filter. 2400 sq ft living space, my panel has 25 of 40 slots in use do I need additional panel, I'm trying to get a good idea of my needs prior to getting price quotes.

Load panel capacity 200 amp [ 1 Answers ]

I have a challenger load panel SB20 (20-40) CT. Which is a 200 amp panel. The number of switches currently in the panel are 19 total. Total amp of all switches is 360. Some of those circuits are dedicated to a sole source. GFCI to Whirlpool tub for example. This panel has 20 1" spots...

200 amp main service panel [ 1 Answers ]

I am planning on upgrading my main service panel (in basement) to a 200 amp service, I want to put a 100 amp sub-panel to the attic for central air and all the lighting on the second floor(about 18 hi-hats and 4 fans). From the 100 amp sub in attic I also want to run a 50 amp breaker feeding a...

Size of 200 amp panel box [ 2 Answers ]

Are there any smaller boxes for updating to 200 amp service than the 36" X 18" standrard box my electrician mentioned. This box would have to be installed in our master bedroom as we have no basement and the existing 100 amp box is in the closet, where he cannot legally install the new service. ...

View more questions Search