Nope, no diagram. Attached are two pics though. One of the sensors close up (when I cleaned them, the other just a general pic. Attachment 45681 Attachment 45682
I have a new flame sensor that also has Hot Spark Igniter (HSI) in the assembly. The original unit however has a spark igniter. The difference between the two is that the HSI has 2-wires, the original spark igniter, has 1-wire.
Is there a way to use the HSI ? I see no Molex board connector for the HSI on the Control Board, where only a single terminal connector was needed for the original spark igniter. I see no way to do it and will get the proper igniter, but figured I'd ask.
Jim,
I don't know that I've ever seen a Smartvalve with spark ignition. Would you please get the number off the valve & post it here? If it is indeed a Smartvalve, the number will start with the letters SV followed by a 4 digit number, maybe a letter & another 4 digit number.
I'm debating on gingerly removing the spark igniter from the old and putting it in the new casing(replacing the current HSI part), but...
1: The ceramic is "well snugged" into the bracket, need to go easy.
2: The wire on the new flame sensor would need to be extended so not sure if that's going to disrupt the nominal ohm signal travel strength.
You have the wrong pilot assembly for the valve. What other controls are on the furnace (igniton control or integrated furnace control) including model numbers?
Here's what I've done: I removed the original Flame sensor from the paired Spark igniter/Sensor clip, then replaced it with the new Flame sensor that was paired with the newly purchased HSI unit.
Furnace has been working perfectly from the first time turning on. I think the Flame sensor is sitting about 1/8 higher than it should be. So to reduce chances of a pre-mature lie-span, I feel I need to lower it.
I attached a video for both a comparison (of the first video), but also to see if the community agrees that too much of the flame sensor may be getting hot. Only the lowest 1/4 inch of the Flame sensor (closest to the porcelain insulator) is staying black.
Jim, I'm a bit confused. You said: "I removed the original Flame sensor from the paired Spark igniter/Sensor clip, then replaced it with the new Flame sensor that was paired with the newly purchased HSI unit." Yet when I watch the new video, I hear spark ignition. What did you replace in addition to the sensor? Part or model number(s) would help me understand.
To answer your question: It does look like the sensor/pilot might be a bit high but if it is in the same position as the original, I don't think I'd mess with it.
Grady,
It was a swap/replace job. I figured since there was no way to retro-fit the HSI, and there no problem getting spark, all I would really need to do is replace the faulty Flame Sensor.
Original unit:
Here is the what I got from eBay:
Result of eBay item:
(NOTICE the melted insulation on the old Flame Sensor)
The video URL in my last reply represents the old spark igniter and holding clip, just with the Flame sensor from the assembly I got on eBay (above). If you would still like additional info(like part #'s) for "fyi" purposes, just let me know. I can provide those.
Thanks. It makes more sense now. What you bought was a pilot/ignitor/sensor assembly for use on a smartvalve. For future reference, what you probably wanted was a Honeywell Q345 series assembly.
I shut off my gas to my Armstrong ultra sx80 furnace now it won't light the thermostat is working with a jumper wire the fan works but seams like no gas is coming true help
Tried to run AC for the first time this season (Furnace works fine).
After looking around, the transformer was definitely burnt.
Bought a new one, swapped it out (after carefully re-connecting the proper wires), and the AC worked.
About a day later, transformer burned out again.
Bought a new...
This all started about a week ago. One night we woke up to a very cold house. The furnace hadn't kicked on at all during the night. It's an Armstrong ultra sx80. It has the automatic ignition. When I went to check on it, I took off the panels and vaccuumed it out and noticed that when I ran the...
I recently experienced a series of small explosions while my furnace was operating. After extensive troubleshooting, I discovered the rollout switch was tripped, after I reset it, I watched the furnace startup properly, but as soon as the blower came on, it had extensive blowback tripping the...