 |
|
|
 |
New Member
|
|
Mar 4, 2007, 12:38 PM
|
|
NO HEAT Rheem Classic 90 series 3 years old
I have a Classic 90 Series Rheem RGRA series upflow/downflow furnace 3 years old. Intermittently, the furnace will not flame up or give out heat. Sometimes it only blows cold air. Sometimes, it locks out (middle green light flashing once then pausing). The furnace repair company came out and said it was the gas line pressure blowing out the flame. That has been ruled out by the gas company, who checked the inflow and outflow pressure. Are there any suggestions? The furnace is still under warranty.
|
|
 |
Ultra Member
|
|
Mar 4, 2007, 12:43 PM
|
|
Well, the service company should be replaced by someone who has a clue. Rheen/Ruud has had more than a few problems with faulty pressure switch's (5 year warranty) I don't know off the top of my head what 1 flash means, it is on the blower door though, also, if the furnace is not properly draining the water, it will act like a pressure switch issue. Good luck.
|
|
 |
New Member
|
|
Mar 15, 2007, 09:47 AM
|
|
 Originally Posted by tw5150
I have a Classic 90 Series Rheem RGRA series upflow/downflow furnance 3 years old. Intermittently, the furnance will not flame up or give out heat. Sometimes it only blows cold air. Sometimes, it locks out (middle green light flashing once then pausing). The furnace repair company came out and said it was the gas line pressure blowing out the flame. That has been ruled out by the gas company, who checked the inflow and outflow pressure. Are there any suggestions? The furnace is still under warranty.
We have same furnace and have had the same problem. Also ignition problem and now the furnace clanks/bangs just before fan comes on.
|
|
 |
Ultra Member
|
|
Mar 15, 2007, 07:14 PM
|
|
 Originally Posted by NorthernHeat
Well, the service company should be replaced by someone who has a clue. Rheen/Ruud has had more than a few problems with faulty pressure switch's (5 year warranty) I don't know off the top of my head what 1 flash means, it is on the blower door tho, also, if the furnace is not properly draining the water, it will act like a pressure switch issue. Good luck.
I agree with NorthernHeat check the drain lines on the furnace. Behind Top door two rubber lines going to drain trap left side of furnace. Trap will exit furnace behind lower door of furnace(blower door). Check for a kink in the line behind top door.(rubber line 1/2 inch)
|
|
 |
New Member
|
|
Mar 20, 2007, 09:01 PM
|
|
 Originally Posted by tw5150
I have a Classic 90 Series Rheem RGRA series upflow/downflow furnance 3 years old. Intermittently, the furnance will not flame up or give out heat. Sometimes it only blows cold air. Sometimes, it locks out (middle green light flashing once then pausing). The furnace repair company came out and said it was the gas line pressure blowing out the flame. That has been ruled out by the gas company, who checked the inflow and outflow pressure. Are there any suggestions? The furnace is still under warranty.
New ignitor
|
|
 |
Ultra Member
|
|
Mar 21, 2007, 04:45 AM
|
|
 Originally Posted by jaisen
new ignitor
If furnace is only 3 years old it has a spark ignitor, not hot surface and shouldn't need replaced. Installers often leave to many pvc filings in the pipes plugging the drain in the venting transition tee or in the trap, it seems to take 2 or 3 years to cause any problems.
|
|
 |
New Member
|
|
Jan 30, 2011, 10:31 PM
|
|
The vacuum line had cracked on my rheem 90.(the one right inside the top panel) Snipped off half an inch, reconnected it, bingo!
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
Heat blowing cold on a Rheem RCBA3765AS17
[ 3 Answers ]
My Rheem central heat and air is not working. Most important now is the heat. The heat comes out, but the air blows cold. Before I spend the money for an expensive expert... is there any hope of me fixing it myself... or doing some checks so I have an idea what is wrong to save time and money if...
Honeywell RTH 7400 Thermostat wiring for Heat Pump (Rheem)
[ 2 Answers ]
I am trying to hook up a Honeywell RTH 7400 Tstat to the existing Rheem HVAC in my house. Currently using Rheem thermostat that came with the house (non-programmeable, using mercury tubes). Heating is provided by a heat pump as well as Natural gas furnace for aux heating (besides the air...
Honeywell thermostat heat/cool in Rheem 2 stage furnace?
[ 1 Answers ]
I have a Honeywell 1 Heat/1Cool thermostat (TH6110D1013) that I would like to use with a Rheem 2 stage gas heat furnace. I think it is possible but would I get the same benefits as having a thermostat with 2 heat/1 cool?
Would I just connect the W terminal on the Thermostat to the W2 on the...
View more questions
Search
|