Ask Experts Questions for FREE Help !
Ask
    adam1976's Avatar
    adam1976 Posts: 2, Reputation: 1
    New Member
     
    #1

    Oct 3, 2011, 12:03 PM
    Heater pilot is lit but burners don't ignite just fan goes on
    It's a carrier heater about 20 years old pilot is on when I turn up thermostat, just the fan goes on filters look clean
    smoothy's Avatar
    smoothy Posts: 25,490, Reputation: 2853
    Uber Member
     
    #2

    Oct 3, 2011, 12:14 PM
    When was the last time it was cleaned and the burners adjusted? Have you killed power to it, waited a few minutes then turned the power back on in case it needed reset?
    adam1976's Avatar
    adam1976 Posts: 2, Reputation: 1
    New Member
     
    #3

    Oct 3, 2011, 12:20 PM
    It was cleaned last year have not tried turning off power to reset it
    parttime's Avatar
    parttime Posts: 1,440, Reputation: 113
    Ultra Member
     
    #4

    Oct 3, 2011, 12:38 PM
    Adam, if the pilot is on and the burners don't light, I would change the thermocoupling. That's cheap and easy. Good luck
    linda1602's Avatar
    linda1602 Posts: 3, Reputation: 1
    New Member
     
    #5

    Jan 2, 2012, 04:44 PM
    Furnace has electric start - after 4 minutes fan comes on but burners don`t light.
    mygirlsdad77's Avatar
    mygirlsdad77 Posts: 5,713, Reputation: 339
    Plumbing Expert
     
    #6

    Jan 2, 2012, 05:06 PM
    Sounds like the pilot flame is not being sensed. If the flame senser doesn't sense the pilot flame, it will not allow the main burners to kick on. So, either the pilot flame is not hitting the flame senser directly, or the flame senser needs cleaning. How many wires lead to the pilot assembly? If only the sparker wire, then the flame is sensed through the sparker.
    mygirlsdad77's Avatar
    mygirlsdad77 Posts: 5,713, Reputation: 339
    Plumbing Expert
     
    #7

    Jan 2, 2012, 05:09 PM
    parttime, actually, if the pilot is lit (and this unit had a standing pilot with a thermocouple, which I don't believe it does) then the thermocouple would be fine. On thermocouple systems, if the thermocouple is bad, the pilot will not stay lit.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Pilot lit but burners will not light [ 1 Answers ]

Pilot is lit but burners will not light

Pilot is Lit, Burners not turning on... [ 0 Answers ]

I have Teledyne Lars Gas Furnace... JVT. The pilot is lit, however the burners aren't firing up. The power venter is on when I call for heat through the thermostats inside the house... I can also hear the forced hot water (actually cold since no burners) moving through the baseboards. I...

Pilot light lit, but burners won't ignite? [ 4 Answers ]

I've got an older Williams model Propane furnace (model # 450sfa-2) controlled by a Lux 1500 Thermostat, and I've tried everything I can think of. The Pilot lights and stays lit, but the burners will not ignite. Any help will be appreciated, it's been cold the last few days (<45 degrees......

Furnace pilot is on, but burners do not ignite [ 1 Answers ]

I have a Carrier furnace 201BB and the pilot comes on but theburners do not ignite all the time. What can I do. Is there a part that needs changed. HELP


View more questions Search