Ask Experts Questions for FREE Help !
Ask
    dmtaft's Avatar
    dmtaft Posts: 3, Reputation: 1
    New Member
    		  
    #1

    Oct 13, 2011, 12:03 PM
    DPDT Switch with light
    I have a DPDT switch that returns to the neutral position. What I want is to be able to wire up a light that turns on and stays on when I push the switch to the "forward" position, then stays on in the neutral position, then the light will only turn off when I push the switch to the "reverse position", then the light again stays off in the neutral position. Does anyone know how to do this?
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
    		  
    #2

    Oct 13, 2011, 12:39 PM
    You can do it with electronics.
    A simple way would be a latching relay.
    May be a problem or not, but you could move the switch OR reverse(up or down) to turn to the opposite condition. You could actually have just a spst momentary pushbutton for this. With a dpdt, maybe even a triple pole double throw switch, then momentary down would be off, and momentary up would be on.
    Some remote controls have a power button, no on and off, it just toggle between the 2 conditions, with 1 momentary switch.
    Can you tell more?
    dmtaft's Avatar
    dmtaft Posts: 3, Reputation: 1
    New Member
    		  
    #3

    Oct 13, 2011, 02:00 PM
    I'm using the DPDT to control a motor where I need to reverse polarity to change direction of the motor. However the motor only stays on for about 2 seconds in either case, this is why I'm using a momentary DPDT that returns to a neutral position. A single coil latching relay sounds like a good solution, I think I'll experiment with that. As for your other suggestions I'm not sure I fully understand how to implement them in conjunction with the momentary DPDT, however thanks for the latching relay suggestion.
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
    		  
    #4

    Oct 13, 2011, 03:10 PM
    If you are needing only 2 seconds, you may not want a latching relay.
    What I might do and since you mention only 2 wires for reversing, I take it you mean a DC Motor.
    On your dpdt switch connect the 4 outer terminals making an "X" . The 2 center terminals can be hooked up to your motor. Then apply your dc voltage to either end of the "X".
    Center will be off and will go forward or reverse for as long as you hold the switch.
    dmtaft's Avatar
    dmtaft Posts: 3, Reputation: 1
    New Member
    		  
    #5

    Oct 13, 2011, 03:27 PM
    Yes it's a DC motor and its currently already wired to the DPDT switch as you described. Now I just want to add the light as simply as possible so that "forward" turns the light on (which then stays on in neutral), while "reverse" turns the light off (which then stays off in neutral). I thought the single coil latching relay sounded good (for controlling the light only), but why then do you say I might not want one?
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
    		  
    #6

    Oct 16, 2011, 07:40 AM
    You could use a diode off switch so it will only light during forward, and will be off in reverse and off condition. Or an Led and a resistor. They only conduct(light)one way.
    I was saying a latching relay may not be desired if only for a couple of seconds. You would have more precise control with releasing the switch?
    What type of light? you are not limited to DC Lighting, a diode and a relay/contactor could control Line voltage or any amount of lighting.

    Edit, I see you want it to stay on in neutral, an SCR could work.
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
    		  
    #7

    Oct 16, 2011, 07:53 AM
    The Silicon-Controlled Rectifier (SCR) : THYRISTORS

    Scroll down to the SCR Testing and the circuit below showing motor or lamp control with a NO switch to start and a NC switch to stop.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

I replaced pull switch lights with recess but the wall switch won't turn off the light [ 2 Answers ]

I added lights and outlets to my basement and all of the outlets work fine. Before I started the switch on the wall controlled one light and all of the others had pull strings. I've tried everything but the switch will not turn off the remaining three lights. What did I do wrong... how do I fix it?...

Can I "share" a 240V dryer outlet using a 30A DPDT switch? [ 0 Answers ]

Hi, I have a dryer in my garage using a 10-30 receptacle. I'm purchasing another device to use in my garge which is 240V 24A and uses a 6-30 plug. I could change this plug to a 10-30 and then simply plug/unplug when I need to swap over from the dryer but this would be a pain to do and I've read...

Need help changing a two wire light switch to a fan and light switch. [ 3 Answers ]

Wall switch box has two black wires and two white wires(spliced. New switch has black wire, red wire(light),yellow wire(fan), and green wire(ground). I think I need an independent wire for the fan and light. How?

Light switch trips itself in off position fed from breaker to switch to outside light [ 1 Answers ]

DPDT slide switch for Hampton Bay Fan [ 1 Answers ]

I have an older Hampton Bay ceiling fan (48") with a slide switch for changing direction. The switch position is presently set for CW and when I move the slide switch to the other direction, the fan stops and will not run until I move the switch to the original position. The other fans in my home...

View more questions Search