 |
|
|
 |
New Member
|
|
Aug 16, 2011, 04:42 AM
|
|
Whirlpool tub starts up by itself.
Do I need to call an electrician or a plumber? I'm assuming it's dangerous.
|
|
 |
Uber Member
|
|
Aug 16, 2011, 04:49 AM
|
|
If the water that comes out of the spout or leaves by the drain,starts by itself, need a plumber.
If the pump for the jets start, then need an electrician.
|
|
 |
Junior Member
|
|
Aug 16, 2011, 06:42 AM
|
|
Need more information, Does tub have air switch or wall switch or both? Either one could be the problem. If it is a electrical problem I would think breaker would trip but would not 100% rely on that. I would try a plumber first. If there is access to the motor, which by code there should be, unplug motor or if tub is on GFI trip it until problem is fixed.
|
|
 |
Eternal Plumber
|
|
Aug 16, 2011, 06:52 AM
|
|
If I had to make a guess it would be a faulty air switch.
Have it checked and replaced if necessary. Good luck, Tom
|
|
 |
New Member
|
|
Aug 16, 2011, 07:33 AM
|
|
The tub has a button that you press (near the top of the tub) to start the whirlpool. That is the only way to start up the whirlpool. No wall switch.
 Originally Posted by speedball1
If I had to make a guess it would be a faulty air switch.
Have it checked and replaced if necessary. Good luck, Tom
Thanks for your input. If it's a faulty air switch, that would require an electrician?
|
|
 |
Eternal Plumber
|
|
Aug 16, 2011, 08:18 AM
|
|
If you're handy and the front apron's removable I can see no reason for you to do the replacement. Be sure to turn off the power at the breaker box before you start. Good luck, Tom
|
|
 |
Plumbing Expert
|
|
Aug 16, 2011, 01:53 PM
|
|
Replace Air Switch Button first before you proceed with replacing anything else. Also, check the air tube connecting Air Switch Box and Air Switch Button for kinks... Milo
|
|
 |
Eternal Plumber
|
|
Aug 16, 2011, 06:25 PM
|
|
Great advice from Milo but I'm sure he meant to add be sure to turn off the power at the breaker box before you work on any electrical appliance,Good luck, Tom
____________
|
|
 |
New Member
|
|
Apr 24, 2012, 06:09 PM
|
|
Agree you're very helpful!! Now to get my husband to work on it... Of course after having to run down to the breaker may have inspired him. This seems to happen when one leans against the back spouts too long (from reading in the tub if that's not too much information). Does that tell you more whether it's the switch or the air tube?
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
Wiring Whirlpool Tub
[ 6 Answers ]
I'm installing a whirlpool tub in my master bedroom. The elctrical requirement is a dedicated circuit for the pump and a circuit for the heater. Both will need to be GFCI protected. I ran a 12/3 cable thinking I can use a double pole 20 A GFCI breaker. However, I have heard it will not work as...
Whirlpool tub on slab
[ 7 Answers ]
Is it OK to raise the tub about 6"? I'm about 3 feet away from the 2" line in the shower drain stubout, and don't wan't to break up all that concrete. I can get the trap in if I raise the tub 6" (I have plenty of head room). Can I build a 7" high form, fill with concrete to about 6 1/2", set the...
View more questions
Search
|