Ask Experts Questions for FREE Help !
Ask
    radaman's Avatar
    radaman Posts: 5, Reputation: 1
    New Member
    		  
    #1

    Apr 14, 2011, 02:17 PM
    In total, approximately how much 1 1 / 2 -inch pipe would be used to make three bends
    In total, approximately how much 1
    1
    /
    2
    -inch pipe would be used to make three bends of
    25 degrees each, assuming that the bend radius is five times the pipe radius?
    radaman's Avatar
    radaman Posts: 5, Reputation: 1
    New Member
    		  
    #2

    Apr 14, 2011, 02:20 PM
    The ends of a run of waste pipe need to be supported with hangers. The length of the
    The ends of a run of waste pipe need to be supported with hangers. The length of the
    Run of pipe is 34 feet 10 inches. Each hanger will be suspended from the same ceiling.
    If the waste pipe will have a grade of
    1
    /
    4
    Inch, how much farther from the ceiling will
    The lower hanger be than the higher hanger?
    radaman's Avatar
    radaman Posts: 5, Reputation: 1
    New Member
    		  
    #3

    Apr 14, 2011, 02:21 PM
    You need to run 44 feet 7 inches of 4-inch cast iron pipe. The run must begin and e
    . You need to run 44 feet 7 inches of 4-inch cast iron pipe. The run must begin and end
    In a hub. Which of the following must you order if you wish to minimize the waste and
    Labor costs?
    radaman's Avatar
    radaman Posts: 5, Reputation: 1
    New Member
    		  
    #4

    Apr 14, 2011, 02:21 PM
    A 3-inch threaded pipe joins the long branch of a 45-degree wye to a 45-degree elbow
    A 3-inch threaded pipe joins the long branch of a 45-degree wye to a 45-degree
    Elbow. What would be the end-to-end length of the threaded pipe if the fittings were
    Offset by 42 inches?
    jlisenbe's Avatar
    jlisenbe Posts: 5,020, Reputation: 157
    Uber Member
    		  
    #5

    Apr 14, 2011, 03:00 PM

    Are you prepping to take some sort of test?
    radaman's Avatar
    radaman Posts: 5, Reputation: 1
    New Member
    		  
    #6

    Apr 14, 2011, 03:07 PM
    Comment on jlisenbe's post
    Yes
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Can a woodstove with an 8 inch pipe use 6 inch chimney pipe? [ 1 Answers ]

I have an old Vigilant woodstove with an 8 inch pipe. I would like to use 6 inch chimney pipe, i.e.. Reduce the pipe diameter from the stove up to the roof. Is there any problem with this: draft, safety, etc?

Connecting 2 inch drain to 1.5 pipe [ 0 Answers ]

I am replacing an old shower pan with a new one. The existing drain line is 1.5 galvanized Steel pipe going underground. I would like to avoid jackhammering up the floor. Is there a reducer or coupling that I can use to convert a 2 inch shower drain into the 1.5 pipe?

One inch gas pipe [ 3 Answers ]

What length of unthreaded one inch gas pipe should be exposed when stubbed out from a finished wall

1/2 inch pipe floor flange [ 2 Answers ]

I am looking for a floor flange for 1/2 inch pipe with a 5-6 inch diameter flange at the floor.

Un-used 3 inch waste pipe [ 2 Answers ]

My house had an option of a second bathroom. The original owner did not go for this option & the plumber put cement in the hub of a 3 inch cast iron waste pipe. I want to now add the second bathroom and I need to use this pipe since it is in the right location. Running a new pipe is out of the...

View more questions Search