Ask Experts Questions for FREE Help !
Ask
    jrk0218's Avatar
    jrk0218 Posts: 1, Reputation: 1
    New Member
     
    #1

    Jan 31, 2007, 09:43 AM
    1992 Honda Civic - Can you interpret OBD-1 error codes?
    The check engine light on my 1992 Honda Civic DX recently came on. When I turned the car off and on again, it was off and only came on after a minute or so. So I thought it was an emissions issue. Anyway, I checked the ECU error codes and got the following: 9 - CYP, cylinder sensor, 17 - VSS, vehicle speed sensor, and 43 - fuel supply system.

    I had the VSS replaced last year (August 2006) and I recently had the 120,000 mile maintenance in April 2006, and the bill says that fuel system was flushed, fuel filter was changed, and the spark plugs, wires, distributor rotor and cap were all replaced.

    Am I getting ripped off here? Or is there yet another problem for me to worry about with this car? It runs fine, and the gas milage hasn't changed, but I notice that at speeds >75-80 mph, it feels like the rpm may be too high.

    Thanks for any help you can provide.
    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #2

    Mar 8, 2012, 07:14 AM
    Taken at face value, the codes thrown cast suspicion on the distributor (Code 9), Vehicle Speed Sensor (Code 17), and possibly Heated Oxygen Sensor (Code 43). When I see so many unrelated codes thrown, I get suspicious, especially when the VSS was recently replaced, that the ECM is good. I would definitely want to find out if the Check Engine Light comes on for 2 seconds and then goes out, when the ignition switch is turned to ON (Position II). Next, I would want to clean the main ECM ground, located on the thermostat housing, and perform the K-Test on the ECM.

    If I was convinced the ECM was good, I would install the Ignition Control Module (ICM) and coil in a new genuine Honda distributor housing, since a Code 9 indicates that the Cylinder Position Sensor (CYP) is bad. Since they are not serviceable, the distributor housing would require replacing. Next, I would clear the ECM, recheck for codes, and check the wiring and connector to the Heated Oxygen Sensor to address the Code 43. If Code 43 persisted, after clearing the ECM again, I would replace the Heated Oxygen Sensor. For the Code 17, I would replace, hopefully under warranty, the VSS.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

94 honda civic obd location [ 8 Answers ]

Yes, I have a 1994 Honda Civic Ex Coupe. The engine code is D16Z6, it's a 1.6L Vtec Motor. Yesterday my check engine light came on. It's the first time this has ever happened since I owned the car. I have had the car since 2000, and have taken excellent care of it. I was wondering if you knew...

Reading error codes on 92-95 Civics (OBD-I Hondas) [ 8 Answers ]

Here is the information you need to read error codes on 92-95 Civic and Del Sol (CRX). Those cars are OBD-I, so the same info should be usable for any other OBD-I Honda. I have not had interest in other Honda cars, so I don't know what year Accords and Preludes are OBD-I. Anyway, off to...

How do I read error codes on a 1990 civic? [ 3 Answers ]

:confused: when I turn the ignition to on (not start) my computer blinks once then pauses and does 16 short blinks? What does this mean? And where is my igniter? I'm getting ready to go to autozone to get my coil and igniter checked... since my cel light doesn't go off... is that why I am having no...

Honda Civic '97 - Error Codes? [ 3 Answers ]

So I've read through the FAQ and all of that, but I do not see any spot to read error codes as was listed in the FAQ, which I assume was meant for the 88-91's. Anyway, my car was dead yesterday, low power/didn't turn over. Took my battery to Sears, the battery is good, which leads me to believe it...


View more questions Search