Ask Experts Questions for FREE Help !
Ask
    bobby30004's Avatar
    bobby30004 Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Dec 17, 2010, 08:28 PM
    The gas comes on lights... and 4-6 seconds it turns off. Ruud Silhouette
    I have a Rudd Silhouette model UGDG-07EAUER Serial # CW5O30Z F0194 4182 - The control board appeared burned and the Gas would not come on. I replaced the control board (honeywell) S9201A with a UT Board 62-24084-82 The draft motor comes one, The ignitor glows, The gas comes on and lights... and 4-6 seconds it turns off. 20-30 seconds later the ignitor again glows, the gas comes on, ignites and again4-6 it turns off at which time the Blower motor comes on. I tried cleaning the flame sensor with steel wool and a I rechecked all connections, what am I missing
    wmproop's Avatar
    wmproop Posts: 3,749, Reputation: 91
    Ultra Member
    		  
    #2

    Dec 17, 2010, 09:14 PM
    Are you sure you replace the right control board? Where did you buy ? And what info about the unit did you use?
    wmproop's Avatar
    wmproop Posts: 3,749, Reputation: 91
    Ultra Member
    		  
    #3

    Dec 17, 2010, 09:15 PM
    I mean with the right /correct control board
    bobby30004's Avatar
    bobby30004 Posts: 2, Reputation: 1
    New Member
    		  
    #4

    Dec 17, 2010, 09:36 PM
    Comment on wmproop's post
    Control board (honeywell) S9201A the replacement part is a UT Board 62-24044-91, though that was not available, I used a Master Replacement Part, UT Board 62-24084-82. This States that is replaces numerous boards, including 62-24044-91
    T-Top's Avatar
    T-Top Posts: 1,871, Reputation: 100
    Ultra Member
    		  
    #5

    Dec 18, 2010, 07:17 PM
    With some of the rudd replacement boards you have to order the flame sensor kit. Its extra.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

I have a RUUD Silhouette II furnace UGLH-07EAUER. The igniter lights but burners nev [ 3 Answers ]

Ruud Silhouette II UGLH-07EAUER. The igniter lights but the burners never come on. The furnace then blows out cold air. What can be the problem?

RUUD Silhouette II intermittent running, ineffective. [ 1 Answers ]

Dang thing won't stay heating. Sometimes will respond perfectly to set-back thermostat for weeks. Then has to be hit in the area of insignia, area of the draft inducer, before flame will start and fan start. The hitting involves significant trek outside, cold outside and inside. This has been...

RUUD Silhouette Furnace/AC UNit Burning up 24v transformers [ 1 Answers ]

I have a 10 yr old Ruud unit that has blown (2) 24vac 40va transformers. Can Anyone tell me what might be causing it. The first one was the original, the second one didn't last the night. Help Please. Thanks

RUUD Silhouette Furnace/AC UNit Burning up 24v transformers [ 1 Answers ]

I have a 10 yr old Ruud unit that has blown (2) 24vac 40va transformers. Can Anyone tell me what might be causing it. The first one was the original, the second one didn't last the night. Help Please. Thanks

View more questions Search