Ask Experts Questions for FREE Help !
Ask
    Diamond94's Avatar
    Diamond94 Posts: 7, Reputation: 1
    New Member
     
    #1

    Jul 28, 2010, 04:09 PM
    I have no water after replacing hot water heater
    I had a small leak in my gas hot water heater so I had my son turn off the water just going to the hot water heater. This causes all of the water in the house to stop after a day. I replaced the hot water heater and turned the water back on, I had intermittent water with low pressure for a few days now I have no water at all. Any help would be appreciated, thank you.
    massplumber2008's Avatar
    massplumber2008 Posts: 12,832, Reputation: 1212
    Senior Plumbing Expert
     
    #2

    Jul 28, 2010, 04:45 PM

    Hi Diamond...

    Sounds like your son may have shut off more than just the cold water feed into the water heater. Here, if he had only shut off the cold water shutoff into the heater and there was an issue it should only be associated with the hot water. You imply above that you have lost both hot and cold... right?

    If you have lost both hot and cold I would look at the MAIN WATER SHUTOFF into the house... at the meter or at the pump. Most likely this has been touched.

    If it has been touched it could even look like it is open but it is actually still closed off... or semi. Closed off... depends on the type of valve.

    If you have only lost hot water then it is certainly reasonable to suspect that the cold water shutof has malfunctioned and needs to be replaced. Here, open the drain at the bottom of the heater and see if water comes out under pressure for a few minutes.

    Let me know what you think...

    Mark
    Diamond94's Avatar
    Diamond94 Posts: 7, Reputation: 1
    New Member
     
    #3

    Jul 28, 2010, 04:51 PM

    He shut off the know above the hot water heater only. I have even gone down and looked myself. The storage tank is empty but has pressure.
    massplumber2008's Avatar
    massplumber2008 Posts: 12,832, Reputation: 1212
    Senior Plumbing Expert
     
    #4

    Jul 28, 2010, 04:55 PM

    Do you have cold water to everything in the house?
    Diamond94's Avatar
    Diamond94 Posts: 7, Reputation: 1
    New Member
     
    #5

    Jul 28, 2010, 04:59 PM

    No water at all, we can hear the pump click every 15 to 20 seconds but there is no water. The gauge on the pipes reads at 0. The pressure in the storage tank is at 30, but there is no or very little water in the tank.
    massplumber2008's Avatar
    massplumber2008 Posts: 12,832, Reputation: 1212
    Senior Plumbing Expert
     
    #6

    Jul 28, 2010, 05:04 PM

    Diamond...

    I don't know much about pumps/pump systems and I don't want to start guessing for you here (not many pumps in Boston area... ;)).

    Give the other guys that hang out here some time to weigh in on this... OK? Check back later tonight and first thing in the AM... hopefully, one of the pump guys will pop in.

    If you can go back (EDIT) your original question and add the fact that your pump system is cycling and the rest you posted that would be very helpful for you.

    Mark
    Diamond94's Avatar
    Diamond94 Posts: 7, Reputation: 1
    New Member
     
    #7

    Jul 28, 2010, 05:09 PM

    Thank you very much.
    Diamond94's Avatar
    Diamond94 Posts: 7, Reputation: 1
    New Member
     
    #8

    Jul 28, 2010, 05:18 PM
    I had a small leak in my gas hot water heater so I had my son turn off the water just going to the hot water heater. This caused all of the water in the house to stop after a day. I replaced the hot water heater and turned the water back on, I had intermittent water with low pressure for a few days now I have no water at all. He only turned the knob at the hot water tank. We hear the pump cycling but there is no pressure in any of the lines. Any help would be appreciated, thank you.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

New hot water heater installed, but no hot water pressure. Plenty of cold water? [ 11 Answers ]

Hi, I own a small plumbing service and have a problem I've never encountered before. I installed a new top vented gas water heater for a customer. Turned the main back on, bled air out of the lines, etc. Problem is there is no hot water pressure throughout the house. Cold water pressure is fine....

Low hot water pressure through the whole house even ater replacing water heater [ 2 Answers ]

I'm still experiencing low hot water pressure even after replacing the water heater. When you first turn on the faucets the pressure will be fine but within a few seconds it drops again.

I have very low hot water pressure from my hot water heafrom an electric water heater [ 0 Answers ]

I have very low water pressure from my hot water heater. I can't find anything wrong.. any ideas?

Electric Hot Water Heater still doesn't heat after replacing thermostats [ 2 Answers ]

Electric Hot water heater was working. Turned well pump off and went on vacation for three weeks. Got back and found I had no hot water. Call Whirlpool, their heater, they told me to replace both upper and lower thermostats after I gave them some voltage and resistive measurements. Replaced...

Electric Hot Water Heater - replacing anode rod [ 3 Answers ]

What is the procedure for replacing the anode that is screwed into the top of an electric hot water tank? In theory it's supposed to be easily replaced, but in real life getting any fitting unscrewed after many years can be a risky. Any tricks or just brute strength? I haven't change it. I...


View more questions Search