Ask Experts Questions for FREE Help !
Ask
    jasonklava's Avatar
    jasonklava Posts: 4, Reputation: 1
    New Member
     
    #1

    Jun 21, 2010, 07:57 PM
    88 ford taurus stalls then starts again
    My 88 Taurus 3.8L V6, stalls every time I step on the accelerator on the first start. I can start it again and be on my way. My routine is too start it, step on the gas to kill it, then start it again. This works for me just to get back and forth to work, while it sits for a while. But if I need to do some running around, and the engine is warm, it dies more often (only when accelerator is depressed). Now, today she stalled during take off at a green light and wouldn't start. Pushed it off to the side of the road, cranks fine, I have fuel pressure at the little bleeder (?) on the fuel rail (looks like a tire stem) fuel squirts out when I stick a poker in there. Well I let it sit for an hour went back to it and it fired right up. New cap, rotor, plugs, fuel filter, air filter. I am a truck mechanic, so I have some experience, but not a very good troubleshooter with this one. Any help will be appreciated!
    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #2

    Jun 21, 2010, 08:21 PM

    Replace the Ignition Control Module (ICM)--AutoZone F125, $42.99. Over time, heat affects the microchip inside. Simple to replace.
    jasonklava's Avatar
    jasonklava Posts: 4, Reputation: 1
    New Member
     
    #3

    Jun 22, 2010, 08:00 PM

    Thank you, but, I cannot find it. I found a picture of one on NapaOnline just to see what mine looks like and I just can't seem to find it. I am searching the web now. By any chance would you happen to know where it's located?
    jasonklava's Avatar
    jasonklava Posts: 4, Reputation: 1
    New Member
     
    #4

    Jun 22, 2010, 08:14 PM
    Where is the ignition control module on an 88 Taurus 3.8L V6?
    I cannot find the ignition control module (ICM) on my 88 Taurus. Is there one? Any help is greatly appreciated!
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
     
    #5

    Jun 22, 2010, 11:33 PM

    RockAuto Auto Parts has it for various prices. It has to be bolted to something because of the heat sink area. Follow the wires to the primary of the coils.
    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #6

    Jun 23, 2010, 06:24 AM

    Follow the wires from the coil--they should lead right to it. It's likely no more than several inches from the coil. Some Fords have them attached to the distributor cap, but I don't believe that's how it is on your car.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Accord '01 stalls but starts after 15-20 minutes [ 16 Answers ]

I have a honda accord 2001. It has stalled on me on the fwy and local streets and it won't start if I turn it off after driving or leaving it running for more than 10 minutes or more. It has 190k and the code reader isn't picking up any code. Can someone please help me?

Tractor starts but stalls [ 1 Answers ]

My lawn tractor has a 17.5 hp b&s and it starts right up and runs for approx. 20 sec. then stalls.I cleaned the carb, put fuel stabilizer in still the same.could it be the fuel solenoid or a faulry safety switch?

Snapper mower starts and stalls [ 1 Answers ]

I've had issues with this mower starting going back to the end of 2006 when I bought a new battery. The mower would click when I turned the key, but not start. The new battery got me through the rest of that season. When spring came, it wouldn't start, so I used my portable charger to jump start...

95 civic starts then stalls [ 1 Answers ]

My civic start for a sec then cut out main relay starts clicking when motor cuts out. Most the time motor won't start and main relay makes clicking sound when trying to start. I replaced the main relay and the ecm.

91 CRX Stalls then starts again [ 1 Answers ]

I've had this car for years, a few years ago the coil went bad and I had it replaced at an auto shop. Several months later it started stalling on me while driving. It wouldn't sputter or anything... it would just shut off. When I go to crank it again, it turns but doesn't start. If I wait maybe an...


View more questions Search